Kohler 15RES Скачать руководство пользователя страница 23

TP-6344 4/09

23

Section 3 Scheduled Maintenance

3.6 Air Cleaner

At the interval specified in the service schedule, inspect,
clean, or replace the air cleaner element. Clean the
element more frequently in dirty, dusty conditions.
Check the element for accumulated oil or dirt that could
cause poor performance.

Replace a damaged air

cleaner element.

Follow the procedure described

below.

Air Cleaner Service Procedure

A dry-type air cleaner silences and filters the intake air.
The air intake silencer assembly connects to the intake
manifold via a flexible hose. Refer to Figure 3-6 during
this procedure.

GM21379

1. Cover
2. Spring clip(s)
3. Housing
4. Pressure tap (1/8-27 NPT)

5. Primary element
6. Dust ejector

1

3

4

5

6

2

Figure 3-6

Air Cleaner

1. Release the spring clips to open the housing and

remove the air silencer element.

2. Tap the element lightly against a flat surface to

dislodge loose surface dirt.

Do not clean the

element in any liquid or use compressed air as
these will damage the filter element.

3. Examine the element and housing for damage.

Replace the element or housing if necessary.

4. Wipe the cover and housing with a clean rag to

remove dirt. Make sure the sealing surfaces fit
correctly and reattach the spring clips.

3.7 Exhaust System

Carbon monoxide.
Can

cause

severe

nausea,

fainting, or death.

The

exhaust

system

must

be

leakproof and routinely inspected.

WARNING

Carbon monoxide detectors.

Carbon monoxide can

cause severe nausea, fainting, or death.

Install carbon

monoxide detectors on each level of the building. Locate the
detectors to adequately warn the building’s occupants of the
presence of carbon monoxide. Keep the detectors operational
at all times. Periodically test and replace the carbon monoxide
detectors according to the manufacturer’s instructions.

At the interval specified in the service schedule, inspect
the exhaust system components (exhaust manifold,
exhaust outlet, exhaust line, exhaust clamps, and
muffler) for cracks, leaks, and corrosion.

Exhaust System Inspection Points

D

Check for corroded or broken metal parts and replace

them as needed.

D

Check that the exhaust outlet is unobstructed.

D

Check the exhaust gas color. If the exhaust is blue or

black, contact your local authorized Kohler distributor/
dealer.

D

Visually inspect for exhaust leaks

(blowby)

. Check

for carbon or soot residue on exhaust components.
Carbon and soot residue indicates an exhaust leak.
Seal leaks as needed.

D

Check that all covers and doors are undamaged, in

place, and locked.

D

Check for the installation and operation of carbon

monoxide (CO) detectors on each level of any
building near the generator set.

Содержание 15RES





































Отзывы: