Kohler 12RES, Руководство по обслуживанию

Страница: 36 / 96

TP-6196 5/04 26 Section 4 Controller
4.5 Controller Configuration and
Adjustment
The first step in troubleshooting the controller is to verify
that the controller is correctly configured for the
generator set.
The controller’s configuration modes
allow setting of the engine type, generator set
configuration (marine, mobile, or standby), data input
types, and other parameters.
The controller configuration for each generator model is
set at the factory.
Changes in the controller
configuration may be required after controller
replacement or other service. Use the instructions in the
following section to check the controller settings and
change them, if necessary.
4.5.1 Controller Time Out
The controller will automatically exit the configuration
mode without saving any changes after about 1 minute
if no buttons are pressed.
Start the configuration
procedure again from the beginning if the controller exits
the configuration mode before the settings have been
saved.
Changes in voltage and speed adjustments are also lost
if they are not saved before the generator set shuts
down. The generator set continues to run with the new
settings until it shuts down but then reverts to the
previous settings at the next startup. Be sure to save
your changes immediately after making adjustments.
4.5.2 Controller Configuration
The controller configuration is factory-set and should
not normally require changes in the field. However, the
controller configuration may need to be checked or
changed during generator set service or controller
replacement.
The controller’s configuration mode allows adjustment
of the system parameters listed in this section. The
system voltage and frequency and unit configuration
and engine type are factory-set for each type of
generator set and engine and should not require
changes unless the controller is replaced.
The controller’s advanced configuration mode allows
the user to set the data input type for engine senders,
toggle the battery voltage between 12 and 24 volts, and
change the controller communications setting for
optional meters (not offered for standby models). Check
these settings after controller replacement and change
them, if necessary, to match the settings shown in
Figure 4-6.
Follow the instructions in Figure 4-7 to enter the
configuration mode while the engine is not running and
then step through the following parameters. Use the up
(
∧
) and down
〈
∨
) arrow buttons to select the appropriate
setting for the application.
Note: Be sure to save your settings before exiting the
configuration mode. The controller reverts to the
last saved settings when the master switch is
moved to the OFF/RESET position.
Voltage/frequency setting (Uu). Select the system
voltage and frequency from the table in Figure 4-6.
Note: This parameter sets the nominal system voltage
and frequency. To adjust the output (measured)
voltage and frequency, see Section 4.5.3,
Figure 4-10 and Figure 4-11.
Unit configuration (Uc). This parameter sets the
generator set type: marine, standby, or mobile. The
setting for the 8.5/12RES is Uc01, standby.
Engine configuration (Ec). The engine configuration
must match the generator set engine type. The engine
configuration setting for the 8.5/12RES is Ec00.
Parameter Setting Definition
Unit’s system voltage
d f
Uu00 Single phase, 60 Hz, 120 VAC y g
and frequency.
Uu01 * Single phase, 60 Hz, 120/240 VAC
Uu05 Single phase, 50 Hz, 115 VAC
Uu06 * Single phase, 50 Hz, 115/230 VAC
Unit configuration Uc01 * 8.5/12 RES (standby)
Engine type Ec00 * 8.5/12 RES
Engine data input types Ed05 * Digital low coolant level, digital pressure, analog temp, with mag. pickup
Bt12 * Battery voltage 12 VDC
Communications Cn00 * No CAN communications
* Factory settings for 8.5/12RES. Choose 50 or 60 hz setting for Uu as required for generator set frequency .
Figure 4-6 8.5/12RES Controller Configuration Parameters