Koeppl Luchs HYDRO LHR-2 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 48

Koeppl Luchs HYDRO LHR-2 Скачать руководство пользователя страница 42

Page 42

Version 02-2010

LHR-2

Maintenance

9.

Fuse

Easy-Drive only

Warning!

Use only the specified fuses. If overrated fuses are used, the electrical system will be destroyed –
risk of fire!
A 15 A fuse must be fitted if a working headlight is additionally used with Easy-Drive!

To replace a defective fuse

•

Remove the cover,

•

remove the defective fuse,

•

insert a new fuse (Easy-Drive only: 10 A, 55W headlight only: 10 A, Easy-Drive with 55W
headlight: 15 A),

•

fit the cover.

10.

Attached devices

In the case of attached devices not covered by this operating manual, the instructions that came
with the respective attached device must be followed.

11.

General

Watch out for fuel and oil leaks and eliminate them if necessary.
Check the tightness of screws, nuts and bolts regularly and retighten them if necessary.
Lubricate all sliding or moving parts (e.g. shift rod joints, Bowden cables etc.) with a little grease
or lubricating oil, especially after cleaning with a high pressure cleaner!

Fuse holder

Cover

Fuse

Holder

Fig. 42. Fuse holder.

Engine

«
...
40
41
42
43
44
...
»

Содержание Luchs HYDRO LHR-2

















































Отзывы:

Нет отзывов