manualshive.com logo in svg

Koeppl Luchs HYDRO LHR-2, Руководство по эксплуатации, Страница: 14 / 48

Поделиться
Скачать
Koeppl Luchs HYDRO LHR-2 Скачать руководство пользователя страница 14

 
 

 

Page 14 

Version 02-2010

 

LHR-2 

Transport 

 

Transport 

 
In order to avoid damage to the machine and life-threatening injuries when transporting the ma-
chine, it is essential to pay attention to the following points: 

•

 

Transport work may be carried out only by persons who are qualified for such work, ob-
serving the safety instructions. 

•

 

The machine may be raised only at the points intended for the purpose and without attached 
devices. 

•

 

When transporting on a trailer, it is essential to secure the machine against slipping and 
rolling away. 

•

 

Use suitable ramps for loading and unloading. 

•

 

Never transport the engine with the fuel tank or the fuel stopcock open. Refer also to the 
motor manufacturer’s operating manual! 

•

 

Obey the national road traffic regulations when driving on public roads. 

•

 

Also read the chapter ‘General safety instructions’. 

 

1. 

Tractor size / machine dimensions 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Fig 3. Luchs HYDRO dimensions. 

Forwards 

107 cm 

39 cm 

21 cm 

29 cm 

5.00x10 
Ø 52 cm 

5.00x10 
Ø 52 cm 

66 cm 

84 cm 

18 cm 

167 cm 

TRACK WIDTHS 

Standard axle 

66 / 80 cm 

80 cm 

88 / 110 cm 

78 cm 

79 cm 

5.00x10 AS 

narrow / wide 

5.00x10 AS 

twin 

21x11x10 AS 

narrow / wide 

20x8x10 AS 

 

23x8.50x12 AS 

 

Spiked roller 

5.00x10 

Hill Spikes  

4.00x10 

131 cm 

136 cm 

Содержание Luchs HYDRO LHR-2

















































Отзывы:

Нет отзывов