Kodak Guidelines 3000 series Скачать руководство пользователя страница 37

Страница: 37 / 79

Setting up the Printer

KODAK PROFESSIONAL Large

Format 3000 Series Inkjet Printers

The “ink refill” message means that ink is being filled into the ink supply system (tubing
and head).

CAUTION:

During ink replenishment, do not turn off the power to the printer.
This may cause damage to your printer. If a power failure occurs
during ink replenishment, do the following:

1. Turn the power switch OFF and then ON. Make sure that no

error messages display on the control panel.

2. Perform a cleaning cycle, and check the test prints.
3. Repeat Step 2 until print quality is acceptable.

NOTE:

•

If ink cassettes are installed and the message “NO

CARTRIDGE” appears, the ink cassettes are not installed
correctly.

Remove the cassette(s) indicated and install it (them)

correctly.

•

If initial ink replenishment fails, clean the head. If the ink

replenishment does not start after several head cleaning cycles,
contact your dealer.

•

If the control panel displays “not original ink” contact your ink

supplier to order KODAK PROFESSIONAL ink cassettes.

Содержание Guidelines 3000 series
















































































Результаты поиска

Содержание Guidelines 3000 series

Отзывы:

Kodak Guidelines 3000 series, Руководство пользователя, Страница: 37 / 79

Результаты поиска

Содержание Guidelines 3000 series

Отзывы: