MINOR CHANGE MACHINE FAMILIARIZATION
2
Dynamic Acera 03/05 Rev. 05
Page 3-68
b5.
ENGINE OIL PRESSURE DISPLAY
This icon will display and the alarm will
sound should the Engine Oil Pressure
drop below a safe operating pressure.
Stop the engine immediately and check engine oil level. Fill en-
gine to proper level with approved motor oil.
If engine has LOW
OIL PRESSURE, it will automatically go to “LO” Idle, and
immediately shut down.
This icon will Display only if alternator is charging.
b6.
ENGINE COOLANT TEMPERATURE DISPLAY
This icon will display and the alarm will
sound should the Engine Coolant Tem-
perature rise above safe operating
temperature.
Reduce engine RPM to idle and stop operation until engine cool-
ant temperature reaches a safe operating temperature range.
b7.
ENGINE AIR CLEANER DISPLAY
This icon will display should the En-
gine Air Cleaner Element(s) (FILTERS)
become too dirty to allow proper air
flow to the engine.
Should this icon display stop engine immediately and clean or
replace Engine Air Cleaner Element(s) as required. This icon
will Display only if alternator is charging.
b8.
OVER LOAD ALARM DISPLAY (Europe only)
This icon will display and the Buzzer
will sound should the Boom Cylinder
Circuit Pressure exceed the set, speci-
fied pressure.
Should this icon display and the buzzer sound, immediately stop
all operation, stop engine and contact an authorized KOBELCO
Service dealer for service assistance.
b9.
BATTERY CHARGING SYSTEM DISPLAY
This icon will display the electrical
charging system not function properly.
Should this icon display, have the elec-
trical charging system repaired imme-
diately.
Icon displays only when engine is running with normal oil pres-
sure and a problem occurs in the charging system.
b10.
FUEL LEVEL DISPLAY
This icon will display should the Fuel
Level in Fuel Tank reaches 54 L (14
Gal) on SK210LC-6E and 60 L (16 Gal)
or less for the SK250LC/SK290LC/SK330LC-6E. Should this
icon display refill fuel tank immediately using approved diesel
fuel.
b11.
HYDRAULIC OIL LEVEL DISPLAY
This icon will display should the Hy-
draulic Oil Level in hydraulic oil reser-
voir fall below safe operating level.
Should this icon display before starting engine, place machine
in Hydraulic Oil Check position and check hydraulic oil level.
Refer to Section 4 for proper instructions to fill hydraulic reser-
voir to proper level using approved hydraulic oil.
This icon will
not display during machine operaton and a loss of hydrau-
lic oil is experienced.
b12.
ENGINE COOLANT LEVEL DISPLAY
This icon will display should the En-
gine Coolant Level fall below safe op-
erating level.
6
LOW E/G
OIL PRESS
7
HIGH E/G
COOL TEMP
9
REST’D AIR
CLEANER
10
ATTACHMENT
OVER LOAD
11
CHARGING
PROBLEM
12
LOW
FUEL LEVEL
13
LOW HYD
OIL LEVEL
Should this icon display before starting the engine, check and
fill coolant level in the radiator and coolant reservoir. Icon will
not display if alternator is charging and a sudden loss of coolant
is experienced.
b13.
ENGINE OIL LEVEL DISPLAY
This icon is displayed when the engine
oil level of the engine oil pan is low.
Check the engine oil level immediately
and make up the shortage of the en-
gine oil.
This icon will not display with engine running and a loss of
engine oil is experienced.
b14.
ATTACHMENT BOOST PRESSURE DISPLAY
This icon will display when the Power
Boost Switch is depressed. This icon
is displayed only when this system is
activated during operation.
b15.
HEAVY LIFT PRESSURE DISPLAY
This icon will display when the Heavy
Lift Switch is in the “ON” position. This
icon is displayed only when this sys-
tem is activated during operation.
b16.
AUTO WARMING UP DISPLAY
This icon is displayed to indicate the
warming up operation of the engine
and hydraulic oil when this system is
activated.
Turn off the auto warm up switch, or the key switch OFF to
cancel the warm up system and the display disappears.
SUPPLEMENTARY EXPLANATION
The LCD of gauge cluster on the machines for Europe displays only
the ISO STD warning icons (Codes No. 1 to 19).
b17.
AUTO WARMING UP FINISH DISPLAY
This icon is displayed when the warm-
ing up of the engine and hydraulic oil
is finished or when the warming up
system is forced to stop.
The monitor alarm will sound continuously for 5 seconds.
b18.
REPLACE ENGINE OIL DISPLAY
This icon will display every 500 hours
of machine operation to remind opera-
tor of scheduled engine oil change.
The recommended oil change interval for MITSUBISHI engines
is every 500 hours of operation. Proceed with engine oil change
and make sure to recalibrate the engine oil change interval.
b19.
HYDRAULIC PRESSURE DRAIN DISPLAY
This icon will display when the hydrau-
lic system pressure drain is activated.
The alarm will sound intermitently dur-
ing the draining process.
b20.
HYD. PRESSURE DRAIN FAIL DISPLAY
This icon will display when the hydrau-
lic system pressure drain process fails.
The alarm will sound continuously.
Turn the ignition key OFF to cancel the alarm and repeat hy-
draulic pressure drain procedure before servicing the machine.
14
LOW E/G
COOL LEVEL
15
LOW E/G
OIL LEVEL
19
POWER
BOOST ON
20
HEAVY LIFT
21
WARMING UP
WARM
28
FINISH
WARM
29
CHANGE
E/G OIL
32
DRAINING
HYD. PRESS
PR
33
FAIL DRAIN
HYD. PRESS
PR
