background image

2  OPERATIONAL DESCRIPTION

In network installations, PS-S.640.30.1 supplies one KNX TP line and monitors all relevant data. With its 
default settings the PS-S.640.30.1 operates as is supposed to.

Communication objects are used to request device status and measurement values. The measured values 
can be sent a er request, a er a certain change (measured value, device status) and periodically. Here, a 
certain  change  of  the  measured  value  means  the  difference  between  actual  value  and  last  sent  value. 
Number and duration of overloads are stored. The same applies for the number of short circuits, device 
startups, KNX bus resets and for the duration of load detachments. The total operating time of the device 
and its operating time since last device startup are stored, too. Threshold values can be set for the bus 
voltage  (only  in  the  additional  alarms),  total  current,  telegram  traffic  and  internal  device  temperature. 
Regarding maximum current values and maximum device temperature values, a tracking period can be 
set. At the end of every tracking period the maximum measured value can be sent on the bus or just be 
set as value of the appropriate object. Four different Alarm tabs (see chapter

 3.7

 ) can be used to send an 

info telegram (containing 

«

0

»

 or 

«

1

»

) about over/under threshold events and to switch other devices. A er 

assignment of the measurement source (

«

Output current

»

«

Device temperature

»

«

Output Voltage

»

) each 

alarm can be configured individually.

2.1  DEVICE/BUSLINE DIAGNOSTICS APPLICATION

The  diagnostic  measurement  sources  and  event  counters  can  be  activated  and  deactivated.  When 
activated, the device monitors the relevant values.

2.2  DIAGNOSIS

The  bus  voltage,  bus  current  and  internal  device  temperature  are  measured  constantly.  The  telegram 
traffic extent is determined additionally. For each of these measurement sources a threshold value can be 
set. A er setting the threshold value the threshold type can be selected (limit undercut/limit exceeded) 
and the behaviour on alarm activation/deactivation can be configured. A maximum value tracking feature 
with pre-settable tracking period can also be activated.

2.2.1  MEASUREMENT SOURCES

page 7

module-electronic.ru

Содержание Module PS-S.640.30.1































Отзывы: