background image

4

ELECTRICAL

ELECTRICAL CONNECTION

This tool is powered by a precision-built electric motor. It should

be connected to a 

power supply that is 120 volts, 60 Hz, AC

only 

(normal household current). Do not operate this tool on

direct current (DC). A substantial voltage drop will cause a loss

of power and the motor will overheat. If the tool does not operate

when plugged into an outlet, double check the power supply. 

SPEED AND WIRING

The belt speed of this tool is approximately 1,900 SFM. This

speed is not constant and decreases under a load or with lower

voltage. For voltage, the wiring in a shop is as important as the

motor’s horsepower rating. A line intended only for lights cannot

properly carry a power tool motor. Wire that is heavy enough for

a short distance will be too light for a greater distance. A line

that can support one power tool may not be able to support two

or three tools.

GROUNDING INSTRUCTIONS

In the event of a malfunction or breakdown, grounding provides a

path of least resistance for electric current to reduce the risk of

electric shock. This tool is equipped with an electric cord having

an equipment-grounding conductor and a grounding plug. The

plug must be plugged into a matching outlet that is properly

installed and grounded in accordance with all local codes and

ordinances.

Do not modify the plug provided. If it will not fit the outlet, have

the proper outlet installed by a qualified electrician. Improper

connection of the equipment-grounding conductor can result in a

risk of electric shock. The conductor with insulation having an

outer surface that is green with or without yellow stripes is the

equipment-grounding conductor. If repair or replacement of the

electric cord or plug is necessary, do not connect the

equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the

grounding instructions are not completely understood, or if

in doubt as to whether the tool is properly grounded.
Repair or replace a

damaged or worn

cord immediately.
This tool is intended

for use on a circuit

that has an outlet like

the one shown in

figure 1. It also has

a grounding pin like

the one shown.

KNOW YOUR BELT/DISC SANDER 

Fig. 1

Grounding

pin

120 V grounded outlet

The safe use of this product requires an understanding

of the information on the tool and in this operator’s

manual as well as a knowledge of the project you are

attempting. Beforeuse  of this product, familiarize

yourself with all operating features and safety rules.

BELT TENSION LEVER

   The belt tension lever releases

the belt tension for easy belt replacement.

BEVEL SCALE

  The worktable comes equipped with a bevel

scale that indicates the degrees the worktable can be tilted 

up to 45°.

MITER GAUGE

  The miter gauge aligns the wood for

positive stops at 90° and 45°.

POSITIONING BOLT

  Loosen the positioning bolt to

change sanding belt positions from horizontal to vertical.

Work

support

Tracking

 knob

Belt tension

lever

Sanding

disc

Sanding belt

Positioning

bolt

Work

table

Miter gauge

Bevel

scale

Switch and

switch key

Fig. 2

SANDING BELT The sanding belt can be adjusted

from horizontal to vertical providing different positions for 

sanding workpieces of different shapes and sizes.
SANDING DISC  A round sanding disc is located on the side 

of the belt/disc sander.
SWITCH AND SWITCH KEY  Your belt/disc sander has an 

easy access power switch.

TRACKING KNOB

  A tracking knob aids in centering the

sanding belt.

WORK SUPPORT (BACKSTOP)

  Supports the work-

piece on the sanding belt.

WORK TABLE

  Equipped with a sturdy work table that

provides a stable surface when using either the disc

sanding or the belt sanding feature.

Содержание KN BD-46B






























Отзывы: