Knick Protos LDO 3400-170 Скачать руководство пользователя страница 20

Страница: 20 / 64

Menu Display

Zero correction

Select module:

The module is in func-

tion check (HOLD) mode. The assigned

current outputs and relay contacts

behave as configured (BASE).

Press

enter

to confirm.

Zero correction:

Display of partial pressure, calibration

temperature and pressure.

Confirm with “OK”.

Select “Zero correction” calibration

method.

Press

enter

to confirm.

Zero Correction

For trace measurements below 500 ppb, the zero point should be calibrated.

If you want to perform a zero correction, then you should keep the sensor in

the calibration medium (eg, N2 or sulfite solution) until the measured value

has stabilized. This may well take several minutes. After that, you can start the

calibration process.

Calibration

Return

25.6°C

Module PH 3400-035

Module CONDI 3400-051

Info

80.3%Air

Module LDO 3400-170

Return

25.6°C

80.3%Air

Automatic - Water

Automatic - Air

Product calibration Sat

Zero correction

Drift check running

Zero correction

25.6°C

80.3%Air

Partial pressure

Abort

0.30 mbar

Calibration / Adjustment

Zero Correction

Calibration temperature

25.6 °C

Calibration pressure

1013 mbar

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos LDO 3400-170

































































Результаты поиска

Содержание Protos LDO 3400-170

Отзывы:

Похожие инструкции для Protos LDO 3400-170

Бренды по названию

Популярные бренды

Knick Protos LDO 3400-170, Руководство пользователя

Результаты поиска

Содержание Protos LDO 3400-170

Отзывы:

Похожие инструкции для Protos LDO 3400-170

Бренды по названию

Популярные бренды