Knick Protos LDO 3400-170 Скачать руководство пользователя страница 14

Страница: 14 / 64

Automatic Calibration in Water

The slope is corrected using the saturation value (100 %) of water in equilib-

rium with air.

During calibration the module is in function check (HOLD) mode.

Current outputs and relay contacts of the module behave as configured

(BASE module).

NOTICE!

The calibration medium must be in equilibrium with air. Oxygen exchange

between water and air is very slow. Therefore, it takes a relatively long time

until water is saturated with atmospheric oxygen. If there is a temperature

difference between calibration medium and measured medium, you must

keep the sensor in the respective medium for several minutes before and after

calibration.

Menu Display

Selecting a calibration mode

Select module:

The module is in func-

tion check (HOLD) mode. The assigned

current outputs and relay contacts

behave as configured (BASE).

Press

enter

to confirm.

Select “Automatic - Water” calibration

method.

Remove sensor and immerse it in cal

medium (air-saturated water).

Press

enter

to confirm.

Calibration

Return

25.6°C

Module PH 3400-035

Module CONDI 3400-051

Info

80.3%Air

Module LDO 3400-170

Return

25.6°C

Automatic - Air

Zero correction

Product calibration Sat

80.3%Air

Automatic - Water

Calibration / Adjustment

Automatic Calibration in Water

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos LDO 3400-170

































































Результаты поиска

Содержание Protos LDO 3400-170

Отзывы:

Похожие инструкции для Protos LDO 3400-170

Бренды по названию

Популярные бренды

Knick Protos LDO 3400-170, Руководство пользователя

Результаты поиска

Содержание Protos LDO 3400-170

Отзывы:

Похожие инструкции для Protos LDO 3400-170

Бренды по названию

Популярные бренды