KNF UFK 1.1100 EX Скачать руководство пользователя

Страница: 6 / 38

Installation Instructions UFK 1.1100 Ex

KNF Flodos UFK1.1100Ex O&M-Rev2

Danger of injuries and damage to property due to leaks at the

interfaces to the pump head

Poisoning and chemical burns or unintended reactions caused by

leaking dangerous substances



Wear personal protective equipment.



Connect the pump correctly.



Operate the pump only when you are sure it has no tech-

nical malfunctions.



Operate the pump in accordance with the technical data.

DANGER

Danger of injuries and damage to property due to uncon-

trolled flow while the pump is not in operation

Poisoning and chemical burns or unintended reactions caused by

leaking dangerous substances



Construct the fluid system so that the operating pressure at

the pressure side of the pump is higher than at the suction

side.



Install a shut-off valve in the fluid circulation system.

The risk analysis indicates a risk of explosion from materials and

substances.

DANGER

Danger of injuries and damage to property due to an explo-

sion in the pump

The pump housing is made from aluminum. If the pump dia-

phragm is damaged, medium can accumulate in the housing and

form hydrogen (especially with acids and lyes). This could cause

an explosion in the pump housing.



Check and monitor the reactivity of the medium with alu-

minum.

The pump housing is designed to withstand pressure surges

caused by explosions. The probability of a fault that would cause

an explosion is deemed to be low. When installed in the system,

the risks in the complete system must be assessed.

Содержание UFK 1.1100 EX







































Результаты поиска

Содержание UFK 1.1100 EX

Отзывы:

Похожие инструкции для UFK 1.1100 EX

Бренды по названию

Популярные бренды

KNF UFK 1.1100 EX, Руководство по установке

Результаты поиска

Содержание UFK 1.1100 EX

Отзывы:

Похожие инструкции для UFK 1.1100 EX

Бренды по названию

Популярные бренды