Knauer Azura VU 4.1 Скачать руководство пользователя страница 42

Страница: 42 / 47

AZURA® Valve Unifier VU 4.1 Instructions V6855

Troubleshooting 33

9.2

Error messages

The display shows the error message. In addition, the status LED blinks

red (see chapter „1.4 Status display“ on page 3). If the red LED does

not blink, the error is fatal. Contact the Technical Support.

Display

Cause of the error

Solution

ERROR:446

RFID tag could not be

read.

Valve is worn out.

Replace the valve.

ERROR:447

RFID tag could not be

written.

Valve is worn out.

Replace the valve.

ERROR:30005

Valve has been repla-

ced during ongoing

operation.

Restart the device.

ERROR:30006

Valve was not recognized. Remount the device.

Note:

If it is not possible to solve the error or if a new error appears,

restart the device. If the error reappears, contact the Technical Support.

Содержание Azura VU 4.1
















































Результаты поиска

Содержание Azura VU 4.1

Отзывы:

Похожие инструкции для Azura VU 4.1

Бренды по названию

Популярные бренды

Knauer Azura VU 4.1, Инструкция по эксплуатации

Результаты поиска

Содержание Azura VU 4.1

Отзывы:

Похожие инструкции для Azura VU 4.1

Бренды по названию

Популярные бренды