Knauer Azura VU 4.1 Скачать руководство пользователя страница 39

Страница: 39 / 47

AZURA® Valve Unifier VU 4.1 Instructions V6855

Operation 30

7.9

Replacing rotor seal

After a defined number of switching cycles, the valve drive reports that

the rotor seal has to be replaced.
The rotor seal has been replaced.

Note:

You find information about the rotor seal replacement in the

docu ment V6864:

www.knauer.net/v6864_en

Process

Figure

After the start display, the message

<REPLACE SEAL!> is shown. This message is

dismissed by press ing any button.

REPLACE

SEAL!

The screen changes to the main display. The

warning sign in the upper right corner shows

that the rotor seal has to be replaced.

POS

1 /16

Change to Seals Count screen:

Main Display > Valve GLP > Seals count

Press the selection button for 3 seconds.

Seals

coun

t 1

The message <Set new seal?> appears.

Press confirmation button. The screen chan-

ges to Seals Count display.

To cancel the process, push another random

button. The screen changes to the Total

Cycles display.

Set new

seal?

Prerequisite

Содержание Azura VU 4.1
















































Результаты поиска

Содержание Azura VU 4.1

Отзывы:

Похожие инструкции для Azura VU 4.1

Бренды по названию

Популярные бренды

Knauer Azura VU 4.1, Инструкция по эксплуатации

Результаты поиска

Содержание Azura VU 4.1

Отзывы:

Похожие инструкции для Azura VU 4.1

Бренды по названию

Популярные бренды