Knauer Azura VU 4.1 Скачать руководство пользователя страница 36

Страница: 36 / 47

AZURA® Valve Unifier VU 4.1 Instructions V6855

Operation 27

7.6

Setting the valve drive control

7.6.1

LAN control

In this submenu is set whether the LAN control is set to manual or via

DHCP.

Process

Figure

Change to control display: Main Display >

Drive Setup > Control

Press selection button.

Change the setting (DHCP/MANL) via the

navigation buttons.

Finish the process by pressing the confirma-

tion button.

Control

LAN MAN

7.6.2

IP Port

In this submenu, the IP port can be set manually.

Process

Figure

Change to IP port display: Main Display >

Drive Setup > IP Port

Press selection button.

Using the navigation buttons, navigate to the

value that has to be changed.

Press selection button.

Using the navigation buttons, set the digit.

Finish the process by pressing the confirma-

tion but ton.

IP Port

1000

7.6.3

LAN settings

In this submenu, the IP adress, netmask and gateway can be set manually.

Process

Figure

Change to LAN Setup display: Main Display

> Drive Setup > LAN Setup

Press selection button.

Using the navigation buttons, navigate to the

value that has to be changed.

Press selection button.

LAN

SETUP

Содержание Azura VU 4.1
















































Результаты поиска

Содержание Azura VU 4.1

Отзывы:

Похожие инструкции для Azura VU 4.1

Бренды по названию

Популярные бренды

Knauer Azura VU 4.1, Инструкция по эксплуатации

Результаты поиска

Содержание Azura VU 4.1

Отзывы:

Похожие инструкции для Azura VU 4.1

Бренды по названию

Популярные бренды