KMC Controls KMD-5210 Скачать руководство пользователя

Страница: 23 / 38



KMD–5210 Installation and Operation

Revision E

Installation

Connecting to a Computer

Connecting to a
Computer

To program the controller with WinControl, a computer must be able to access
the controller. Choose from one of the following connection methods.

◆

Modem

◆

Ethernet

◆

EIA–232 connection

Installing a modem interface

By adding an optional modem to the modem port, an off-site computer can
access the controller through a dial-up connection. The modem connection
also supports dial-in and the Control Basic functions

TPAGE

and

NPAGE

. If

the modem port is enabled, Computer B port is disabled and is not available
for direct connection with a computer.

Note

KMC Controls recommends using U.S. Robotics modems for off-site
communications. KMC does not offer support for other modem installations.

To install a modem:

1. Connect a a standard DB-9 to DB-25 computer-to-modem cable between

the KMD–5569 modem and a serial port on a computer on which
WinControl is installed. This cable is available from computer supply
sources.

2. Connect the modem to a telephone line dedicated to the network system.

Illustration 2-11 KMD–5569 modem connection to KMD-5210 controller

KMD–5569

modem

Standard 9–pin to

25–pin cable.

Содержание KMD-5210







































Результаты поиска

Содержание KMD-5210

Отзывы:

Похожие инструкции для KMD-5210

Бренды по названию

Популярные бренды

KMC Controls KMD-5210, Инструкция по установке и эксплуатации

Результаты поиска

Содержание KMD-5210

Отзывы:

Похожие инструкции для KMD-5210

Бренды по названию

Популярные бренды