KMC Controls KMD-5210 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 38

background image

KMC Controls

Revision E

Installation

Planning for input and output modules

20

Planning for input
and output
modules

To connect inputs or output devices to a KMD-5210 controller, use KMD-5220
input and KMD-5221 output modules. The KMD-5210 controller includes
eight universal I/O ports for up to eight KMD-5220 input modules, eight
KMD-5221 output modules or any combination of up to eight modules.

Each module connects to the controller using a flat ribbon cable. When
connecting input and output modules, use the following guidelines.

◆

Connect the first KMD-5220 input module to connector

I/O Card 1

; add

continue adding input modules from left to right

◆

Connect the first KMD-5221 output module to connector

I/O Card 8

and

continue adding output modules from right to left.

◆

Use ribbon cables no longer than 24 inches (61 cm).

◆

KMD-5221 output modules require an output transformers.

Illustration 2-8 Typical input and output module connection

«
...
18
19
20
21
22
...
»

Содержание KMD-5210







































Отзывы:

Нет отзывов

Похожие инструкции для KMD-5210

Бренд: Banner Страницы: 15

Бренд: bar Страницы: 2

Бренд: Eaton Страницы: 12

Бренд: National Instruments Страницы: 31

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 85

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 98

CompactRIO cRIO-9002

Бренд: National Instruments Страницы: 21

Бренд: National Instruments Страницы: 145

Бренд: National Instruments Страницы: 42

Бренд: National Instruments Страницы: 8

Бренд: National Instruments Страницы: 54

Бренд: Saab Страницы: 4

Бренд: National Instruments Страницы: 72

Бренд: National Instruments Страницы: 41

MAGNUM ALERT 3000 FIRE ALARM

Бренд: NAPCO Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды