manualshive.com logo in svg

KMC Controls 69 Series, Руководство оператора

Поделиться
Скачать
KMC Controls 69 Series Скачать руководство пользователя страница 9

7 

This  safety  alert  symbol  is  used  throughout  this  manual  to  identify  safety  messages.  
When you see this symbol, read the message which follows as it will advise you of  
possible injury. 

BEING SAFETY CONSCIOUS IS GOOD BUSINESS! 

SAFETY 

This  symbol  indicates  an  imminently  hazardous  situation 
that, if not avoided, will result in death or serious injury. 

This symbol indicates a potentially hazardous situation that, 
if not avoided, could result in death or serious injury.  It may 
also be used to alert against unsafe practices. 

This symbol indicates a potentially hazardous situation that, 
if not avoided, may result in minor or moderate injury.  It may 
also be used to alert against unsafe practices.

 

REMEMBER 

THINK SAFETY! 

SYMBOL INFORMATION 

Is used for instruction on operating, adjusting, or servicing a 
machine.

 

(RED) 

(ORANGE) 

(YELLOW) 

(GREEN 

OR 

BLACK) 

Содержание 69 Series



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды