manualshive.com logo in svg

KMC Controls 69 Series, Руководство оператора

Поделиться
Скачать
KMC Controls 69 Series Скачать руководство пользователя страница 39

37 

Front Coulter Adjustment 

 

Front coulters are set at the factory to be directly aligned with the ripper shanks. This is important 

for  smooth  residue  flow  around  the  shank.  If  the  coulter  is  not  properly  aligned,  loosen  the  3/4in    
hardware  on  the  U-bolt  and  slide  the  mount  bracket  over  until  the  coulter  is  aligned.  Retighten          
according to the torque specification chart in the “

General

” section of the “

Assembly  Setup

”  part of 

the manual. 

 

 

The coulter swivel stop setscrew should be pointed straight forward to ensure equal amounts of left 

to right swivel.  

 

 

The  offset  of  the  coulter  stem  should  also  be  pointed  straight  forward.  When  the  shanks  reset   

themselves after clearing an obstacle, the point swings forward and could hit the coulter if the offset is 
not forward. 

 

 

The vertical position of the front coulters should be adjusted according to the shank working depth. 

To adjust the height of the coulter, simply loosen the (2) 5/8in setscrews, one at a time, that hold the 
coulter stem in the mounting bracket as shown below. Caution should be taken when loosening these 
setscrews  as  the  stem  can  drop  suddenly  if  it  is  not  being  supported.  Once  the  setscrews  are  loose, 
pickup/lower  the  coulter  stem  to  the  desired  position  and  retighten  the  (2)  5/8  setscrews.  Proper       
procedure  for  tightening  setscrews  is  to  tighten  to  proper  torque,  loosen,  then  retighten  to  proper 
torque.  This  allows  the  setscrew  to  “set”  itself  in  the  coulter  stem  and  provides  maximum  holding    
capability.  (See  Bolt  Torque  Chart)  The  chart  below  shows  the  stem  height  values  for  “A”  and  the   
corresponding shank working depth values. Exact coulter position may differ from this initial setting 
depending on how much coulter down pressure is needed for particular soil and residue conditions.  If 
coulter hub is dragging on residue or pushing dirt, then raise stem higher.  If more down pressure is 
needed  to  cut  residue,  then  position  stem  lower.    At  any  height,  the  coulter  arm  should  not  be           
continuously against the upper limit stop or coulter/stem damage may occur.  

 

Stem  

Height  

“A” 

Shank  

Working 

Depth 

1 in 

≤ 12in  

2-3/4 in 

13in-15in 

4-1/2 in 

16in-18in 

Содержание 69 Series



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды