manualshive.com logo in svg

KMC Controls 69 Series, Руководство оператора

Поделиться
Скачать
KMC Controls 69 Series Скачать руководство пользователя страница 41

39 

OPTIONAL ATTACHMENTS 

Spiked Roller Adjustments 

 

The spiked roller on the back of the Subsoiler Leveler is used to gauge the working depth of the 

shank. Any adjustments done to the height of the spiked roller will directly affect the depth at which 
the shank penetrates the ground. Adjusting the height of the roller is done through the ratcheting turn-
buckles that hold the top of the roller pivot brackets to the roller reaches. (See assembly set-up instruc-
tions for more information.) To adjust the height of the roller simply ratchet the turnbuckles in/out until 
the  desired  roller  height  is  reached.  Below  is  a  chart  showing  the  length  between  clevis  pins  on  the 
ratcheting turnbuckle and the corresponding shank working depth. Since the rollers are held by multi-
ple  turnbuckles,  it  is  best  to  adjust  each  turnbuckle  in  small  increments  until  the  desired  length  is 
reached in order to avoid putting the roller mount tube in a bind.  

Spiked Roller Scraper Adjustments 

The  scraper  attachment  on  the  spiked  roller  is 
used to keep soil from building up on the surface 
of the roller. The scraper is adjusted vertically by 
loosening the (2) bolts holding the scraper to the 
support  angle  and  sliding  the  scraper  down.  As 
the  scraper  wears,  and  when  it  is  adjusted,  it  is 
important  to  maintain  the  1/8in  dimension       
between  the  edge  of  the  scraper  and  the  roller. 
This  dimension  is  designed  to  maximize         
performance and minimize scraper damage. 
 

The  scraper  is  held  in  position             

horizontally  by  the  U-bolts  connecting  the 
scraper  angle  to  the  roller  support  tube.  The 
scrapers should be adjusted so the spikes on the 
roller pass between the scraper fingers with equal 
amounts  of  room  on  each  side.  After  the  initial 
setting,  the  horizontal  spacing  should  not  need 
further adjusting. 

TURNBUCKLE 

LENGTH 

SHANK 

WORKING 

DEPTH 

20 1/2” 

18” 

21” 

17” 

21 1/2” 

16” 

22” 

15” 

22 1/2” 

14” 

23” 

13” 

23 1/2” 

12” 

25” 

11” 

27” 

10” 

Содержание 69 Series



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды