manualshive.com logo in svg

KMC Controls 69 Series, Руководство оператора

Поделиться
Скачать
KMC Controls 69 Series Скачать руководство пользователя страница 25

23 

RIPPER TOOL OPTIONS: 

A TRIPPED SHANK IS UNDER EXTREME 
FORCE.    STAY  CLEAR  OF  A  TRIPPED 
SHANK!    FAILURE    TO    COMPLY  WILL 
RESULT IN SERIOUS INJURY OR DEATH. 

DANGER 

The 6900 Series Subsoiler Leveler comes equipped with a choice of the Reset on the Go Ripper Shank 
or the Toggle Trip Shank.  Either of these will be pre-mounted to the bar when the unit arrives.  Verify 
the pre-mount location of all the shanks by using the “

Overhead  Layout

” portion of this section. It 

may  be  necessary  to  mount  some  of  the  wear  items  associated  with  these  ripper  shanks  using  the      
following: 
 

For the KMC Ripper Points use (1) 3/8 x 1 1/4” long roll pins to secure in place on each shank as 

shown.  For KMC Shank Wear Shins use (3) 5/16 x 1 3/8” long roll pins to secure to each shank as 
shown.    Once  all  items  on  each  shank  are  in  place  verify  that  all  hardware  is  in  place  and  properly 
tightened and secured. 

Toggle Trip Shanks 

SHANK WEAR SHIN 

5/16 X 1 3/8 ROLL PINS 

3/8 X 1 1/4 ROLL PIN 

RIPPER POINTS 

Reset-On-The-Go Shanks 

SHANK WEAR SHIN 

5/16 X 1 3/8 ROLL PINS 

3/8 X 1 1/4 ROLL PIN 

RIPPER POINTS 

Содержание 69 Series



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды