Klutch 101670 Скачать руководство пользователя страница 13

Page 13 of 20 

 

Maintenance 

WARNING

 

Always wear protective gauntlets before changing saw blade! 

Changing the Saw Blade 

1. 

Remove the protective casing unscrewing the six screws. 

2. 

Loosen the blade tension, turning the knob E in the anti-clockwise direction. 

3. 

Extract the blade first from the guides and then from the cast iron pulleys. 

4. 

Insert the new blade first between the guides and then into the cast iron pulleys, checking to 
make sure the blade teeth are facing toward the work piece.

 

 

5. 

Turn the knob E to adjust the blade tension. 

6. 

Replace the protective casing. 

7. 

Reposition the blade guides in the correct position for next cut. 

 

Maintain the product by adopting a program of conscientious repair and maintenance in accordance 
with the following recommended procedures. It is recommended that the general condition of any tool 
be examined before it is used. Keep your tool in good repair. Keep all cutting tools sharp and clean. 
Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to 
control. Keep handles dry, clean, and free from oil and grease. 

Also refer to the engine manufacturer’s 

instruction manual for additional information about engine maintenance. The following chart is based 
on a normal operation schedule. 

Maintenance 
Interval 

Maintenance Point 

Every 3 months 

Check blade for dullness and replace if necessary. 

Every 2 months 

Usually check the condition of the power supply cords and replace them if 
they are broken, or even worse if the internal wires are shown. 

Содержание 101670





















Отзывы: