Klutch 101670 Скачать руководство пользователя страница 10

Page 10 of 20 

 

 

Positioning the work stop 

Use the work stop if you have to do several cuts on pieces of the 
same length. 

1. 

Loosen the lock handle A and place the work stop at the 
desired distance from the blade.  

2. 

Retighten the lock handle. 

 

  

 

 

CAUTION

 

Make sure that the work stop does not interfere with the downward movement of the blade!

 

 

Cutting angle adjustment 

The band saw can cut at angles from 0º to 60º. 

1. 

Loosen the lock handle B. 

2. 

Turn the swivel support until the mark on support 
matches desired angle on the scale. 

3. 

Retighten the locking handle. 

 

CAUTION! Make sure the lock handle B has been 
tightened before turning on the machine. 

  

 

 

CAUTION

 

Make sure the lock handle B has been tightened before turning on the machine. 

 

Adjusting the blade guide 

The sliding blade guide must be adjusted to bring the 
guide close to the material. If the adjustment is not 
done, it will result in an unclean cut. 

1. 

Loosen the lock handle C. 

2. 

Slide  the  blade  guide  to  move  it  closer  to  the 
workpiece.  

Swivel support 

Содержание 101670





















Отзывы: