Kitagawa TP530 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 35

Kitagawa TP530 Скачать руководство пользователя страница 26

9-2 ウォームギヤのバックラッシ量の調整方

法

9-2 Backlash adjusting method of worm

gears

この調整作業は、ＮＣ円テーブルの割出精

度、及び、ウォームギヤの耐久性に影響を
与えるため、調整技術を身に着けた作業者
が行なうことが望まれます。ご購入先、又
は、お近くの北川鉄工所営業所までご相談
の上、作業を行なってください。

This adjustment affect the indexing
accuracy and worm wheel durability, thus it
is strongly recommended that a skilled
technician should do the adjustment.
Please consult Kitagawa distributor before
the adjustment.

危険

DANGER

バックラッシ調整を行う場合には、必ず制

御装置の電源を OFF、または NC 円テーブル
をアンクランプ状態にした後に行って下さ
い。

回転中に誤って手や衣服がギヤに触れる

と巻き込まれて大事故につながる恐れがあ
ります。

Be sure to turn OFF the power source of
control unit or unclamp the NC rotary
table before removing the gear case cover.

If your hands or clothes touch the rotating
gears, there is a danger to cause a serious
accident by winding to the gears.

1) 潤滑油を排油口より抜きます。

2) カバー①を取り外します。

3) ベアリングケース②を固定している六

角穴付ボルト③を少し緩めます。次に
アジャスティングスクリュ④4 本を均
一に少し緩めます。再度六角穴付ボル
ト①を締め込むと、ベアリングケース
②が前進することにより、ウォームギ
ヤのバックラッシが小さくなります。

1) Drain the lubrication oil from the drain

port.

2) Remove cover

①

.

3) Loose hexagon socket head cap screws

③

which fix the baring case

②

a little.

Next, loosen four adjusting screws

④

uniformly a little. When tightening
hexagon socket head cap screws

③

again, the bearing case

②

advances,

thus reducing the backlash of worm
gears.

株式会社北川鉄工所

/

KITAGAWA IRON WORKS CO

．，

LTD.

9-3

«
...
24
25
26
27
28
...
»

Содержание TP530




































Отзывы:

Нет отзывов