Kipor IG6000 Скачать руководство пользователя страница 10

Страница: 10 / 38

2.3 Service Rules



Use genuine KIPOR or KIPOR recommended parts and lubricants or their equivalents. Parts that
do not meet Kipor’s design specifications may damage the engine and void the warranty.



Use special tools designed for the product when specified.



Always install new gaskets, O-rings, etc. when reassembling components.



Clean parts in cleaning solvent upon disassembly. Lubricate any sliding surfaces before

reassembly. After reassembly, check all parts for proper installation and operation.



Many screws used in this machine are self-tapping. Be aware that cross-threading or over

tightening these screws will strip the threads and ruin the hole.



Use only metric tools when servicing this engine. Metric bolts, nuts and screws are not

interchangeable with non-metric fasteners. The use of incorrect tools and fasteners will damage

the engine.

2.4

Electrical Precautions



Hold the connector body to disconnect the connector. Do not disconnect by pulling the wire

harness. To disconnect the locking connector, be sure to unlock first, and then disconnect.



Check the connector terminals for bend, excessive extrusion, missing terminals, or other

abnormalities before connecting the connector.



To connect, insert the connector as far as it goes. If the connector is a locking type, be sure that it

is locked securely.



Check the connector cover for breakage and check whether the connector female terminal is not

opened excessively. Then, connect the connector securely. Check the connector terminal for rust.

Remove the rust using an emery paper or equivalent material before connecting the connector.



Set the harness clips in the specified places of the frame securely, and secure the wire

harnesses.



Clamp the cables securely.



Clamp the wire harnesses securely so that they do not interfere with the rotating parts, moving

parts and hot parts.



Route and connect the wire harnesses properly. Be sure that the harnesses are not slack,

twisted or pulled overly taut.

Содержание IG6000







































Результаты поиска

Содержание IG6000

Отзывы:

Похожие инструкции для IG6000

Бренды по названию

Популярные бренды

Kipor IG6000, Руководство по обслуживанию

Результаты поиска

Содержание IG6000

Отзывы:

Похожие инструкции для IG6000

Бренды по названию

Популярные бренды