background image

4

4

-

53

Function description and operating tips

(1) wheel bolt (nut)    (2) rim bolt

(3) rim 

  (4) disc

(a) Forward

rear wheel installation pattern

3

4

1

2

3

4

1

2

A

A

d21o449a

wheel installation direction

For  agricultural  tires,  make  sure  to 

install  them  with  their  arrow  marks 

on their side pointing the front driving 

direction.
the  tire  is  correctly  installed  if  the 

tread  mark  “v”  on  the  ground  is 

shown  correctly,  not  up  side  down, 

while the tractor is moving forward.

rear  tire  specs and  wheel 

bolt/nut torque

tire size (agri)

13.6-24 / 6pr

warning

use tires approved by Kioti only.

assemble the tire as shown in 

the figure.

contact your local Kioti deal-

er if it is necessary to change 

the tire specification or instal

-

lation method.


tightening torque of wheel bolt (nut)

196~225 n·m

144~166 lbf-ft

20 ~ 23 kgf·m

Front tire specs and wheel 

bolt/nut torque

tightening torque of wheel bolt (nut)

196~225 n·m

144~166 lbf-ft

20 ~ 23 kgf·m

warning

use tires approved by Kioti 

only.

assemble the tire as shown in 

the figure.

contact your local Kioti deal-

er if it is necessary to change 

the tire specification or instal

-

lation method.



tire size (agri)

8-16 / 6pr

TD210-미국법인향-DK4210,4710,5310,60153   53

2020-11-18   오후 2:35:26

Содержание DK4210(C)HSE























































































































































































































Отзывы: