Kioti DK4210(C)HSE Скачать руководство пользователя страница 174

Страница: 174 / 214

Dk4210(c)hse / Dk4710(c)hse / Dk5310(c)hse / Dk6010(c)hse

111

Item

Tightening torque

front

wheel

Bolt

225 n·m

166 lbf·ft

20~23 kgf·m

nut

rear

wheel

Bolt

nut

ChECkING WhEEl BOlT/NUT TORQUE (Q)

(1) front wheel Bolt/nut

(2) rear wheel Bolt/nut

check wheel bolts and nuts regu-

larly especially when new. if they are

loose, tighten them as follows.

CAUTION

To avoid injury:

Never operate tractor with a

loose rim, wheel, or axle.
Any time bolts and nuts are

loosened, retighten to speci-

fied torque.

Check all bolts and nuts fre-

quently and keep them tight.

•
•

•

D21o708a

FUEl FIlTER (s)

REMOVING WATER FROM FUEl FIlTER

1. water and dust in fuel are accumu-

lated in the filter. Remove the plug

from the bottom of the fuel filter to

drain any impurities.

2. Tighten the filter with a hand (not a

tool) after drainage.

3. start the engine and check for fuel

leakage.

TD210-미국법인향-DK4210,4710,5310,60122 22

2019-09-18 오후 4:53:36

Содержание DK4210(C)HSE























































































































































































































Результаты поиска

Содержание DK4210(C)HSE

Отзывы:

Похожие инструкции для DK4210(C)HSE

Бренды по названию

Популярные бренды

Kioti DK4210(C)HSE, Руководство пользователя

Результаты поиска

Содержание DK4210(C)HSE

Отзывы:

Похожие инструкции для DK4210(C)HSE

Бренды по названию

Популярные бренды