background image

4

4

-

Function description and operating tips

the turn signal lights are used when 

turning the vehicle left or right. pull-

ing the lever up blinks the right turn 

signal  light  while  pushing  the  lever 

down blinks the left turn signal light.

turn signal light switch

the  horn  switch  can  be  operated 

without  the  key  inserted.  pressing 

this switch sounds the horn.

this  switch  can  be  used  to  warn 

other  vehicles  when  malfunction  oc-

curs in the tractor while driving on a 

public  road.  pressing  this  switch  up 

blinks the hazard lamp and returning 

it turns off the lamp. the turn signal 

lights  cannot  be  operated  while  this 

switch  is  pressed  up  to  operate  the 

hazard lamps. 

hazard lamp switch

horn switch

note

the turn signal light lever is not 

the self-return type. therefore, 

make sure to return the lever 

manually after turning the vehicle.
the turn signal lamps can be op-

erated without the key inserted.

A

B

11

A

B

td2o407s

(1) turn signal light switch

(a) right turn 

  (b) left turn

11

td2o408s

1

A

B

1

A

B

td2o409s

(1) horn switch

(1) hazard warning Flasher switch

(a) on 

  (b) oFF

TD210-미국법인향-DK4210,4710,5310,6019   9

2020-11-18   오후 2:34:46

Содержание DK4210(C)HSE























































































































































































































Отзывы: