background image

7

SAFETY INFORMATION

WARNINGS Cont.

LOCAL CODES

Install and use fireplace with care. Follow all local codes. In
the absence of local codes, use the latest edition of The
National Fuel Gas Code ANSI Z223.1, also known as NFPA
54*. Firebox must be electrically grounded in accordance
with the National Electrical Code, ANSI/NFPA 70 (latest
edition).

*Available from:

American National Standards Institute, Inc.

National Fire Protection Association, Inc.

1430 Broadway

BatterymarchPark

New York, NY 10018

Quincy, MA 02260

FOR YOUR SAFETY READ BEFORE LIGHTING

A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.

Before lighting

, smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is

heavier than air and will settle on the floor.

What to do if you smell gas

• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.

C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand,

don’t try to repair it, call a qualified service technician or gas supplier. Force or attempted repair may result in a fire or
explosion.

D.  Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the

appliance and to replace any part of the control system and any gas control which has been under water.

WARNING

If you do not follow these instructions exactly, a fire or
explosion may result causing property damage, personal
injury or loss of life.

17. Turn off appliance and let cool before servicing. Only a

qualified service person should install, service and repair 
appliance.

18.  Inspect the appliance before use and at least annually by

a professional service person. Frequent cleaning may be
required due to excessive lint from carpeting, bedding
material, etc. It is important that control compartment,
burner and circulating air passage of the appliance be
kept open.

19. When operated for the first time, there will be some

smell from the appliance. This will diminish and
disappear after a few hours of operation.

20.

Warning: 

Do not allow fans to blow directly into the

fireplace. Avoid any drafts that alter flame patterns.

21.

Warning: 

Do not use a blower insert, heat exchanger

insert or other accessory not approved for use with this
heater.

22.  The firebox canopy must not be replaced with a canopy

which may be provided with the decorative type
UNVENTED room heater.

23.

Warning: 

Do not operate ceiling fans in same room as

the vent free appliance.

24. Must be installed by a licensed gasfitter in the

Commonwealth of Massachusetts. Complies to code
527CMR.

25. Unvented gas fired appliances may be used only for

supplemental heat and/or decorative purposes and under
no circumstances shall they provide a primary heat
source.

Содержание ZVF33

















































Отзывы: