background image

2

Why does my fireplace or stove give off odour?

It is normal for your fireplace to give off some odour.  This is due to the curing of the paint, adhesives,
silicones and any undetected oil from the manufacturing process as well as the finishing materials used
with the installations (e.g. marble, tile and the adhesives used to adhere this product to the walls can
react with heat and cause odours).

It is recommended that you burn your gas fireplace or stove for a minimum of four hours at a time with
the fan off after the curing of the paint has been completed.  These odours can last upward to 40 hours
of burn time, keep burning at a minimum of four hours per use until odours dissipate.

About curing of the paint

Your stove or fireplace has been painted with the highest quality silicone stove paint.  This paint dries
quickly in 15-20 minutes when first applied at the factory.  However, due to the high temperature sili-
cone components, the paint will cure when heat is applied to the appliance as it is first used. 
The following information 

applies to the curing process

to get the paint fully hard and durable.

Fire the appliance four successive times for 10 minutes each firing and a 5 minute cool down between
each.  Be aware during log and firebox paint curing that a white deposit may be developing on the
inside of the glass doors.  It is important to remove this white deposit from the glass doors with an
appropriate cleaner to prevent build-up (such as Windex or a commercial fireplace glass cleaner).

• Babies, small children, pregnant women and pets should leave the area during the cure phase.

• Ventilate well, open doors and windows.

• Do not touch during curing.

Noise coming from the fireplace?

• Noise caused by metal expanding and contracting as it heats up and cools down, similar to the

sound produced by a furnace or heating duct.  This noise does not affect the operation or longevi-
ty of your fireplace.

PRE-INSTALLATION QUESTIONS and ANSWERS

Содержание IDV33-IDV36






























Отзывы: