Kingsman Fireplaces HBZDV4736, Руководство по установке

Страница: 35 / 81

Gas Line Installation
This gas appliance should be installed by a qualified installer in accordance with local building codes and with current CAN/CGA -
B149.1 or .2 installation codes for Gas Burning appliances and equipment in Canada and the National Fuel Gas Code ANSI Z223 in the
U.S.A.
1. The gas pipeline can be brought in through
either the right or the left side of the appliance.
A knockout is provided at either location
to allow for the gas pipe installation and
testing of any gas connection.
2. The gas control inlet is 3/8” NPT. Typical
installation layout for rigid pipe is shown at
right.
3. When using copper or flex connector , use
only approved fittings. Always provide a
union so that gas line can be easily
disconnected for burner or fan servicing. See
gas specification for pressure details and ratings.
4. When a vertical section of gas pipe is
required for the installation, a condensation trap is needed. See CAN/CGA-B149.1 or .2 for code details.
5. For natural gas, a minimum of 3/8” iron pipe with gas minimum pressure of 4.5” w.c. must be used for supply from the
gas meter. Consult with the
local gas utility if any questions arise concerning pipe sizes.
6. A 1/8” NPT plugged tappings are accessible for test gauge connection both on the inlet and outlet of the gas valve.
7. Turn the gas supply ON and check for leaks. DO NOT USE OPEN FLAME FOR THIS PURPOSE. Use an approved
leak testing solution.
8. The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any
pressure testing of that system at
test pressures in excess of 1/2 PSIG (3.5 KPa).
9. The appliance must be isolated from the gas supply piping system by closing its individual shutoff valve during any
pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 PSIG (3.5 KPa).
Note: The gas line connection may be made of 1/2” rigid pipe or an approved flex connector. Since some
municipalities have additional local codes, it is always best to consult your local authorities and the current
CAN/CGA - B149.1 or .2 installation code in Canada or the National Fuel Gas code ANSI Z223.1 in the U.S.A.
Gas Specifications
Models MQHBZDV MQRB
HB4736N HB4736LP 4236N 4236LP 3636N 3636LP 4236N 4236NT 4236LPT
Fuel Natural Propane Natural Propane Natural Propane Natural Natural Propane
Gas Control Millivolt Adjustable
Maximum Input HI [Btu/hr] 40,000 36,000 30,500 29,200 30,500 29,200 30,500 24,000 24,000
Maximum Input LO [Btu/hr] 27,000 30,000 20,600 22,200 20,600 22,200 20,600 18,000 19,000
Maximum Output HI [Btu/hr] 27,200 24,100 23,180 22,100 23,200 21,900 23,180 - -
Orifice Size (0-4500ft) #31 #49 #36 #51 #36 #51 #36 #42 #53
Air Shutter Opening 5/16" Fully Open 3/16" 5/16" 3/16" 5/16" 1/16" 1/32" 1/4"
Gas Inlet Size S.I.T. 820 Nova, 3/8" NPT
Gas Supply Pressure Minimum Normal Maximum
Natural Gas [in. w.c.] 5.5" 7" 9"
Propane [in. w.c.] 11" 11" 12"
Manifold Pressure Nat. Gas Propane
High [in. w.c. / kPa] 3.5" / 0.87 10" / 2.61
Low [in. w.c. / kPa] 1.6" / 0.40 6.3" / 1.57
For the state of Massachusetts a T-handle gas shut-off
valve must be used on a gas appliance. This T-handle gas
shut-off valve must be listed and approved by the state of
Massachusetts. This is in reference to the state of
Massachusetts state code CMR238.
HB4736N
NE/2
HB4736LP
LPE/2
4236LP
LPE/2
4236N
NE/2
3636LP
LPE/2
3636N
NE/2
4236N
NE/2
4236NT
NTE/2
4236LPT
LPTE/2
Shutoff valves installed in tubing systems
shall be rigidly and securely supported
independently of the tubing.
Important: Always check for gas leaks with
a soap and water solution. Do not use open
flame for leak testing.
35