KidKraft F29655 Скачать руководство пользователя

Страница: 57 / 92

SCALE:1:50

WEIGHT:

Roof -Gable Connect

SHEET 2 OF 2

REV.

DWG. NO.

SIZE

•Attach Gable to inside Roof Supports with #8 x 1/2 Pan Screws

•Repeat for other side

Hardware

1 x

Front Small Roof

1 x

Back Small Roof

Wood Parts

2672

Place (2672) Front Small Roof against (2671) Back Small Roof so the tops form a peak then tight to the

inside edge of the outside slats attach 1 Narrow Angle Bracket per slat with 2 (S0) Truss Screws per bracket.

(fig. 24.2)

Place Small Roof Support Assembly against one side so the peaks meet and the ends of the roof supports

are flush with the ends of the roof panels. Attach with 6 (S11) Wood Screws. (fig. 24.2)

Attach 1 Sky Gable to the inside of the (2680) Roof Supports with 4 (S5) Pan Screws. (fig. 24.3)

Step 24: Small Roof Assembly

Part 2

6 x

Wood Screw

4 x

Truss Screw

4 x

Pan Screw

S11

2671

2672

Flush

Small Roof

Support

Assembly

Other Parts

2 x Narrow Angle Bracket
1 x Sky Gable

x 2 per

bracket

Narrow Angle

Bracket

Flush

Fig. 24.2

S11

Fig. 24.3

2680

Sky Gable

Содержание F29655





























































































Результаты поиска

Содержание F29655

Отзывы:

Похожие инструкции для F29655

Бренды по названию

Популярные бренды

KidKraft F29655, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F29655

Отзывы:

Похожие инструкции для F29655

Бренды по названию

Популярные бренды