KidKraft F29655 Скачать руководство пользователя

Страница: 29 / 92

On the Back Wall, from inside the

assembly, tight to the End Wall, halfway up

the assembly, 5/8” (15.9 mm) down from the

top of the panel board attach 1 (2777) Side

Joist MOD to (2677) Narrow Panel and (2772)

Panel Floor Support with 2 (H11) Hex Bolts

(with lock washer, flat washer and t-nut).

Bolts are installed from inside the assembly.

Make sure (2777) Side Joist MOD is level

then attach with 4 (S3) Wood Screws. (fig.

4.9 and 4.10)

Tight to (2777) Side Joist MOD, 5/8” (15.9

mm) down from the top of the panel board

attach (2682) Short Side Joist to (2772) Panel

Floor Support with 1 (H11) Hex Bolt (with

lock washer, flat washer and t-nut). Bolt is

installed from inside the assembly. Make sure

(2682) Short Side Joist is level and flush to

the top of (2777) Side Joist MOD then attach

with 2 (S3) Wood Screws. (fig. 4.9 and 4.10)

Repeat E and F for the Front Wall, except

(2777) Side Joist MOD is tight to the Swing

Wall and (2682) Short Side Joist is attached

to (2677) Narrow Panel. (fig. 4.9 and 4.10)

12 x

Wood Screw

6 x

Hex Bolt (lock washer, flat washer, t-nut)

Hardware

Top View

2 x

Side Joist MOD

2 x

Short Side Joist

Wood Parts

2777

2682

Tight

2777

(hidden)

2677

H11

Fig. 4.10

Fig. 4.9

H11

2677

2777

2772

2682

Front

Wall

Back Wall

2682

2677

2772

2682

2777

2622

H11

2777

Tight

Step 4: Frame Assembly

Part 4

End Wall

FW1

LW1

TN1

5/8”

15.9

Swing Wall

Front Wall

Back Wall

Содержание F29655





























































































Результаты поиска

Содержание F29655

Отзывы:

Похожие инструкции для F29655

Бренды по названию

Популярные бренды

KidKraft F29655, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F29655

Отзывы:

Похожие инструкции для F29655

Бренды по названию

Популярные бренды