manualshive.com logo in svg

KidKraft F29655, Инструкция по установке и эксплуатации, Страница: 27 / 92

Поделиться
Скачать
KidKraft F29655 Скачать руководство пользователя страница 27

 27 

Fig. 4.6

Flush

Flush

Notice back 

(2677) Narrow 

Panel overlaps 

End Wall

WL5

WL5

Notice End Wall 

overlaps front 

(2677) Narrow 

Panel

2677

Back

2677

Front

Flush

Flush

Top View

Details

SHEET 1 OF 9

A

SIZE DWG.  NO.

REV.

SCALE:1:50

WEIGHT: 

Pre-drill using 3/16" drill bit for 1/4 x 2½ Lags

Use #8 x 7/8" Truss screws for the Jamb Mounts

Do not cover the 2 holes with Jamb Mounts

WL5

x 4 per 

side

2 x 

Narrow Panel

Wood Parts

Hardware

8 x 

Wafer Lag

WL5

End Wall

Step 4: Frame Assembly 

Part 2

B:

  Place End Wall between 2 (2677) Narrow Panels noticing the panel orientations.  The tops and bottoms of 

the panels should be flush.   Make sure the panels are square then using the pilot holes as a guide pre-drill with 

a 3/16” (4.8 mm) drill bit and fasten the back (2677) Narrow Panel to End Wall and End Wall to the front (2677) 

Narrow Panel with 4 (WL5) Wafer Lags per side.  (fig. 4.4, 4.5 and 4.6)

Fig. 4.4

Fig. 4.5

2677

End Wall

2677

2677

Back

Front

Содержание F29655





























































































Отзывы:

Нет отзывов