KidKraft F29655 Скачать руководство пользователя

Страница: 44 / 92

Wood Parts

Hardware

Other Parts

Step 14: Rock Wall Assembly

Lay 2 (2776) Rock Rails down, side by side with angled edges

facing down. (fig. 14.1)

Place (2779) Access Board on the bottom of each (2776) Rock Rail

as shown in fig. 14.1. Make sure (2779) Access Board is flush to the

outside and bottom edges of each (2776). Attach using 4 (S2) Wood

Screws.

7-5/8” (193.6 mm) down from the top of both (2776) Rock Rails

place 1 (2781) Rk Board B, making sure the sides are flush to the

outside edges of each (2776) Rock Rail. Attach using 4 (S20) Wood

Screws. (fig. 14.1)

In between the (2779) Access Board and (2781) Rk Board B

stagger 2 (2781) Rk Board Bs and 2 (2780) Rk Board As using 4 (S2)

Wood Screws per board. Placing them as shown in fig. 14.1, this will

prevent rocks from forming a straight line. Make sure the boards are

evenly spaced and do not exceed 2-3/8” (60.3 mm) between boards.

Place 1 rock on each (2780) Rk Board A

and (2781) Rk Board B (fig. 14.2) and attach

using 1 (PB2) Pan Bolt (with lock washer,

flat washer and barrel nut) and 1 (S10) Pan

Screw per rock. The Screw must be in the

hole directly under the Pan Bolt, it will stop the

rock from spinning. (fig. 14.3)

Note: Gaps between boards 2-1/4” (57

mm), not to exceed 2-3/8” (60.3 mm)

Note: The holes

in the rock boards

must orient to the

top of the boards.

7-5/8” (193.6 mm)

Approx

Fig. 14.1

2779

2776

2780

2781

2780

Fig. 14.2

1 x

Access Board

3 x

Rk Board B

2 x

Rk Board A

2 x

Rock Rail

24 x Wood Screw
5 x

Pan Screw

5 x

Pan Bolt

(lock washer, flat washer & barrel nut)

2776

2780

2781

2779

Rock

5 x Rocks (3 green/2 yellow)

S10

PB2

Fig. 14.3

x 4 per

board

FW0

LW1

BN1

Содержание F29655





























































































Результаты поиска

Содержание F29655

Отзывы:

Похожие инструкции для F29655

Бренды по названию

Популярные бренды

KidKraft F29655, Инструкция по установке и эксплуатации

Результаты поиска

Содержание F29655

Отзывы:

Похожие инструкции для F29655

Бренды по названию

Популярные бренды