KidKraft Cedar Summit F25745 Скачать руководство пользователя

Страница: 5 / 135

About Our Wood

Cedar Summit Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s
use.

Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to

weathering which can change the appearance of your set.

What causes weathering? Does it affect the strength of my Play System?

One of  the main reasons for weathering is the effects of  water (moisture); the moisture content of  the wood at the surface is
different than the interior of  the wood. As the climate changes, moisture moves in or out of  the wood, causing tension which can
result in checking and or warping. You can expect the following due to weathering. These changes will not affect the strength of
the product:
1.

Checking

is surface cracks in the wood along the grain. A post (4” x 4”) will experience more checking than a board (1” x 4”)

because the surface and interior moisture content will vary more widely than in thinner wood.

Warping

results from any distortion (twisting, cupping) from the original plane of the board and often happens from rapid

wetting and drying of the wood.

Fading

happens as a natural change in the wood color as it is exposed to sun-light and will turn a grey over time.

How can I reduce the amount of weathering to my Play System?

At the factory we have coated the wood with a water repellent or stain. This coating decreases the amount of water absorption
during rain or snow thus decreasing the tension in the wood. Sunlight will break down the coating, applying a water repellant or
stain on a yearly basis is important maintenance. (see your local stain and paint supplier for a recommended product)
Most weathering is just the normal result of nature and will not affect safe play and enjoyment for your child. However if you are
concerned that a part has experienced a severe weathering problem please call our consumer relations department for further assistance.

warranty service.

province to province. This warranty excludes all consequential damages, however, some states do not allow the

limitation or exclusion of consequential damages, and therefore this limitation may not apply to you.

10 Year Limited Warranty

Cedar Summit by KidKraft

warrants that this product is free from defect in materials and workmanship

for a period of one year from the original date of purchase. In addition, lumber is warranted for 10

years against structural failure due to rot and insect damage. All other parts, such as hardware, swings,

rides, accessories, and slides carry a one-year warranty only.

This warranty applies to the original owner and registrant and is non-transferable.

Regular maintenance is required to assure the integrity of your Play System. Failure by the owner

to maintain the product according to the maintenance requirements may void this warranty. This

warranty does not cover any inspection cost.
This Limited Warranty does not cover:

• Labour for replacement of any defective item(s);

• Incidental or consequential damages;

• Cosmetic defects which do not affect performance or integrity;

• Vandalism; improper use or installation; acts of nature;

• Minor twisting, warping, checking, or any other natural occurring properties of wood that do not

affect performance or integrity.

Cedar Summit by KidKraft products have been designed for safety and quality. Any modifications

made to the original product could damage the structural integrity of the unit leading to failure and

possible injury. Cedar Summit by KidKraft cannot assume any responsibility for modified products.

Furthermore, modification voids any and all warranties.

This product is warranted for

RESIDENTIAL USE ONLY

. Under no circumstance should a

Cedar Summit

by KidKraft

Play System be used in public settings such as schools, churches, playgrounds, parks, day cares

and the like. Such use may lead to product failure and potential injury. Any and all public use will void this

warranty.

Cedar Summit by KidKraft disclaims all other representations and warranties of any kind, express or implied

[email protected]

Содержание Cedar Summit F25745








































































































































Результаты поиска

Содержание Cedar Summit F25745

Отзывы:

Похожие инструкции для Cedar Summit F25745

Бренды по названию

Популярные бренды

KidKraft Cedar Summit F25745, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cedar Summit F25745

Отзывы:

Похожие инструкции для Cedar Summit F25745

Бренды по названию

Популярные бренды