KidKraft Cedar Summit F25745 Скачать руководство пользователя страница 103

Страница: 103 / 135

103

Fig. 57.4

Fig. 57.5

It is important to note hole orientation for the following steps.
F:

Loosely attach each Climbing Crater Rock with 1 (PB2) ¼ x 1-1/4” Pan Bolt (with lock washer, flat washer and

barrel nut) per rock. Maneuver each rock so that the second hole lines up with the pre-drilled hole in the board.

Insert Pan Bolt into the second hole as a pin holding Climbing Crater Rock in place and mark the location for the 3rd

hole.

Remove Pan Bolt from second hole and swing Climbing Crater Rock out of the way. Drill a 3rd hole in the

marked location using a 3/8” Drill bit.

Install remaining 2 (PB2) ¼ x 1-1/4” Pan Bolt (with lock washer, flat washer and barrel nut) in each rock and

tighten all bolts.

Note: Make sure all hardware is used and tightened to secure each rock properly.

Step 57: Assemble Rock Wall

Part 3

use bolts as a guide in two pre-

drilled holes, mark 3rd hole,

remove rock and drill with 3/8" drill bit,

attach with all three bolts

3/16” Flat

Washer

1/4”

Barrel

Nut

1/4” Lock

Washer

Climbing

Crater

Rock

PB2

Hardware

12 x

1/4 x 1-1/4” Pan Bolt

(1/4” lock washer, 3/16” flat washer & 1/4” barrel nut)

PB2

Other Parts

4 x Climbing Crater Rock

Содержание Cedar Summit F25745








































































































































Результаты поиска

Содержание Cedar Summit F25745

Отзывы:

Бренды по названию

Популярные бренды

KidKraft Cedar Summit F25745, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Cedar Summit F25745

Отзывы:

Бренды по названию

Популярные бренды