manualshive.com logo in svg

KidKraft Cedar Summit BEAR CAVE LODGE FSC, Инструкция по установке и эксплуатации

Поделиться
Скачать
KidKraft Cedar Summit BEAR CAVE LODGE FSC Скачать руководство пользователя страница 80

 80 

2 x        Upper Post 1-1/4 x 3-1/4 x 58-7/8”
2 x        Short Post 1-1/4 x 3-1/4 x 36-3/4”
2 x        Roof Side 5/8 x 3-1/4 x 40-1/8”
1 x        Side Top 15/16 x 3-1/4 x 30-7/8”
1 x        Tunnel Side Top 15/16 x 3-1/4 x 30-7/8”

6023

6029

6030

6012

6000

Wood Parts

Hardware

Step 39: Upper Frame Assembly

Adventure Tower Assembly

A:

 Place 1 (6012) Short Post and 1 (6000) Upper Post side by side with the (6012) Short Post on the left side making 

sure that the notched out end is at the bottom and facing the outside. Place (6023) Roof Side at the top of the posts 

so that it’s flush and attach using 2 (H2) ¼ x 2” Hex Bolts (with lock washer, flat washer and t-nuts). 

(Fig. 39.1)

B:

 Place (6029) Side Top so it lines up with the lower pre-drilled holes on the posts and attach using 2 (H2) ¼ x 2” 

Hex Bolts (with lock washer, flat washer and t-nuts). 

(Fig. 39.1)

C:

 To make a second partial upper frame assembly place 1 (6012) Short Post and 1 (6000) Upper Post side by side 

with the (6012) Short Post on the right side, notched side facing out and the (6000) Upper Post on the left side. Place 

(6023) Roof Side at the top of the posts making sure it’s flush and attach using 2 (H2) 1/4x 2” Hex Bolts (with lock 

washer, flat washer and t-nuts). 

(Fig. 39.2)

 

D:

  Place (6030) Tunnel Side Top so it lines up with the lower pre-drilled holes on the posts and attach using 2 (H2) ¼ 

x 2” Hex Bolts (with lock washer, flat washer and t-nuts). 

(Fig. 39.2)

 

Set the upper assemblies aside, they will not be used until a later step.

H2

8 x 

1/4 x 2” Hex Bolt (LW1, FW1, TN1)

Fig. 39.2

6012

H2

X4

loosely assmble

6030

H2

6000

6023

2 angles shown, pick the best one

square each sub assembly 

D

add 1/4" T-Nut to inside  

of Long Post

Fig. 39.1

6012

6029

6023

6000

H2

H2

2 angles shown, pick the best one

square each sub assembly 

D

add 1/4" T-Nut to inside  

of Long Post

2 angles shown, pick the best one

square each sub assembly 

D

add 1/4" T-Nut to inside  

of Long Post

TN1

TN1

LW1

LW1

LW1

FW1

FW1

FW1

TN1

TN1

TN1

FW1

FW1

LW1

LW1

Содержание Cedar Summit BEAR CAVE LODGE FSC





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды