5
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Toggle
®
Tables - Triple Motor C-Leg Height-Adjustable Square Shoe Base, Model SS
Assembly Instructions
This product is for use on a nominal 120-volt circuit and has a grounding plug
that looks like the plug illustrated in Detail F. Make sure that the product is
connected to an outlet having the same configuration as the plug. No adapter
should be used with this product.
GROUNDING INSTRUCTIONS
Table Wiring
Note:
Control cables can be routed
differently than shown. Tables may
have the control box mounted either
between the cross-tube assemblies
on the longer side of the table or
centered in front of the square shoe
leg. Follow directions appropriate to
control box mounting location.
Note:
When plugging leg control
cord ends in, make sure to push in
straight to avoid bending any pins
in the electrical control box or leg
motor. The plug will click when it is
locked into place.
Note:
If any plug needs to be
removed, make sure power cord is
un-plugged from power source outlet
first. Then push down on release
tab on the control cable plug while
simultaneously pulling on the end to
remove from the socket.
1.
Leg Cord - Long:
Plug the longer
leg control cord into one of the
three rectangular sockets on the
control box, then route cord to the
leg farthest from control box. Use
cut outs in the table to route under
the cross tubes and/or use zip ties
secured with screws at pre-drilled
locations. Cables can also be routed
on the sides of the middle leg and
under the middle support brackets to
route around the cross-support tubes
as illustrated in Figure 6. Plug other
end of the longer leg control cord
into the open socket on leg motor
(Figure 6).
2.
Leg Cord - Short:
The next
rectangular socket on the control box
is utilized by the shorter leg control
cord. Plug short leg cord into control
box and route to the leg motor socket
that is closest to the control box.
Use cut outs in table to route under
the cross tubes. Cables can also be
routed on the sides of the middle
leg and under the middle support
brackets to route around the
cross-support tubes as illustrated
in Figure 6. Plug other end of the
shorter leg control cord into open
socket on leg motor (Figure 6).
3.
Key Pad:
The key pad mounts in
one of two locations on the front
side of tabletop (Figure 6). Using
pre-drilled holes, secure key pad to
tabletop with two M4.2 x 19
flat head screws at 1.5 ft/lb.
Note:
Do not overtighten screws. Once key
pad is mounted, route attached cord
to control box. Once the key pad
cord is routed to control box, plug
cord into the round socket on box
(Figure 6).
Note:
Make sure all cables are
routed correctly and plugged into
correct sockets on control box and
leg motor locations before installing
zip-ties.
4.
Zip-ties:
Six zip-ties are included
for keeping cords tight to table, but it
is not necessary to use all six. Using
Figure 6 for reference, wrap the
zip-ties around the loose cords and
then mount the zip-tie to the tabletop
with a M5.5 x 22 pan head screw into
the pre-drilled holes. The zip-ties
have a built in mounting hole which
must lay flat onto surface. Make sure
zip-ties and cables are snug before
moving to next step.
5.
Power Cord:
The final cord to be
installed is the power cord. Plug
power cord into remaining open
socket which is tri-lobe in shape.
Cord should not be zip-tied or routed
through cut outs on table (Figure 6).
Do not plug it into power source at
this time.
6. If optional R8 power module was
specified for installation, go now to
page 6. If optional wire trough was
specified for installation with no R8
power module, go now to page 7. If
no wire trough is specified, carefully
turn table to the upright position with
the help of another person. Adjust
glides on feet to level the table. Plug
the power cord into a grounded
outlet power source (Detail F).
Note:
Power cord must have enough
slack so the table can cycle through
its entire range of motion.
7.
The table must be “zero set”
prior to being placed into
service. Refer to table “zero
setting” instructions in the
trouble shooting guide on
page 9.
8. If the table is not operating properly,
see the trouble shooting guide in this
instruction.
Figure 6
leg control
cord (short)
power
cord
square shoe
tabletop
leg control
cord (long)
leg
motor
key
pad
M4.2 x 19
flat head screws
(max torque is 1.5 ft/lb)
keypad
cord
leg control
cord (long)
leg
motor
middle-support
bracket
M4.2 x 19
flat head screw
M5.5 x 22
pan head
screw
M5.5 x 22
pan head
screw (six)
zip-tie
(six)
Detail F
grounding
pin
grounded
outlet
