2
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Toggle
®
Tables - Triple Motor C-Leg Height-Adjustable Square Shoe Base, Model SS
Assembly Instructions
Figure 2
leg-to-leg
spanners
(long)
leg column
assembly
(at long end)
C-leg
foot
foot
plate
M8 x 12
button-head
machine
screw
mounting
flange of
motor
housing
C-leg
end-support
tube
cross-support
tube (short)
set screw
holes
M6 x 35
socket head
cap screws
adjustable
glide
M8 x 12
button-head
machine screw
M6 x 35
socket head
cap screw
cross-support
tube (short)
cross-support
tube (long)
cross-support
tube (long)
USER
SIDE
USER
SIDE
square shoe
tabletop (long end)
(shown for reference)
Detail B
C-leg
end-support
tube
M8 x 12
button-head
machine
screw
leg-to-leg
spanner
(short)
cross-support
tubes (short)
with no
leg-to-leg
spanner
Detail C - 30” x 48” x 60” &
30” x 60” x 48” Tables
End C-Leg Assembly
(long end of table)
Note:
There are two different lengths
of cross-support tubes and leg-to-leg
spanners. The long end of the table
uses two short and two long
cross-support tubes and two long
leg-to-leg spanners. The two longer
support tubes must be installed to
the back, longer, non-user side of the
table (Figure 2).
1. Start assembling the C-leg to be
placed on the long end of the
table by positioning one shorter and
one longer cross-support tube (with
mounting tabs facing down and facing
inwards), and one C-leg end support
tube in position as illustrated in
Figure 2. The longer cross-support
tube must be positioned to the back,
longer, non-user side of the table.
Place a leg column assembly over
the three support tubes and align six
mounting holes of the leg column
mounting base with appropriate
mounting holes of the three tubes as
illustrated. The C-leg end support
tube contains three mounting holes
but only the two non-user side holes
are used. Make sure the tube has the
longer end with one unused mounting
hole facing the user side as illustrated
in Detail B. Using six M8 x 12 button
head machine screws torqued to
9.5 ft/lb, secure the flange of the leg
column to the three support tubes
(Figure 2).
2. Assemble the C-leg foot to the leg
column by first positioning a plastic
foot plate over the mounting location
on the leg column. The foot plate
must be oriented so the raised flange
faces into the column, to nest the foot
plate into place. Next, position a foot
over the foot plate and leg column as
illustrated, with the mounting holes
of the foot aligning with those of the
leg column. It is important that the
longer end of the C-leg foot face the
user side. Once the foot is correctly
oriented, secure the foot to the leg
column with four M6 x 35 socket
head cap screws. Torque to 7.5 ft/lb
(Figure 2).
Note:
If the table being assembled
is 30” x 48” x 60” or 30” x 60” x 48”,
the leg-to-leg spanner on the longer,
user side of the table is not required
and must
NOT
be installed. Unused
spanner(s) may be disposed of
(Detail C).
3. Position the two longer leg-to-leg
spanners with their channel openings
face up, then slide both spanners into
the open ends of the cross-support
tubes installed under the leg column
base. Next slide a cross-support tube
(matching the same length as at the
opposite end of the leg-to-leg
spanner) onto each end of the
leg-to-leg spanners (with mounting
tabs face down and facing inward).
Do not secure the support tubes to the
spanners with set screws at this time
(Figure 2).
