background image

Assemble units as described herein only. To do otherwise 
may result in instability. All screws, nuts and bolts must be  
tightened securely and must be checked periodically after  
assembly. Failure to assemble properly, or to secure parts 
may result in assembly failure and personal injury.

13

Genesis

®  

Desking - Modesty Panel 

Assembly Instructions

Modesty Panel Installation

(optional)

1.  Identify correct length modesty 

panel for length of table side (60” 

and 48” shown). Radius bends (if 

applicable) orient toward corner post 

or peninsula post leg (Figure 28).

2. Remove the protective paper backing 

on modesty panel felt pads to expose 

the adhesive surface. Position a felt 

pad centered on the top and bottom 

of each modesty panel mounting 

bracket face and apply firm pressure 

to allow adhesive to set (Figure 28).

2.  Rotate mounting brackets at an angle 

to fit between panel flanges. Rotate 

mounting brackets vertically to lock 

in place on panel (Figure 29).

3.  Attach assembled modesty panel to 

holes on underside of worksurface. 

Use two #14 x 1” Phillips screws for 

mounting each bracket (Figure 30).

Figure 30

#14 x 1”

Phillips screws

Figure 29

modesty panel

flanges top and

bottom

rotate mounting brackets vertical

to lock in place on panel and
slide to approximate location

on panel

modesty

panel

Figure 28

modesty

panel

felt pads

modesty panel

mounting

bracket

Содержание Genesis Desking

















Отзывы: