Keysight U1401B Скачать руководство пользователя

Страница: 148 / 159

Performance Tests and Calibration

148

Keysight U1401B User’s and Service Guide

Adjustment Considerations

To adjust (calibrate) the instrument, you will need a set of test input cables and

connectors for receiving the reference signals. You will also need a shorting plug.
Adjustments for each function should be performed with the following

considerations (where applicable):
– Allow the instrument to warm up and stabilize for five minutes before

performing the adjustments.

– Make sure that the batteries will not run low during the adjustments. Replace

or recharge the batteries before making adjustments to avoid false reading.

– Consider the thermal effects as you connect the test leads between the

calibrator and this instrument. It is recommended that you wait for one minute

after connecting the test leads before you begin the calibration.

– During ambient temperature adjustment, ensure that the instrument has been

turned on for at least one hour with a K-type thermocouple connected

between the instrument and the calibration source.

CAUTION

Do not turn off the instrument during calibration. This may delete the

calibration memory for the present function.

Содержание U1401B
































































































































































Результаты поиска

Содержание U1401B

Отзывы:

Похожие инструкции для U1401B

Бренды по названию

Популярные бренды

Keysight U1401B, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U1401B

Отзывы:

Похожие инструкции для U1401B

Бренды по названию

Популярные бренды