Keysight U1401B Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 159

background image

Keysight U1401B User’s and Service Guide

5

WARNING

– Inspect the test probes for damaged insulation or exposed metal, and

check for continuity. Do not use the test probe if it is damaged.

– Do not use any other AC charger adapter apart from the one certified by

Keysight with this product.

– Do not use repaired fuses or short-circuited fuse-holders. For continued

protection against fire, replace the line fuses only with fuses of the same
voltage and current rating and recommended type.

– Do not service or perform adjustments alone. Under certain condition,

hazardous voltages may exist, even with the equipment switched off. To
avoid dangerous electric shock, service personnel must not attempt
internal service or adjustment unless another person, capable of
rendering resuscitation or first aid, is present.

– Do not substitute parts or modify equipment to avoid the danger of

introducing additional hazards. Return the product to the nearest
Keysight Technologies Sales and Service Office for service and repair to
ensure the safety features are maintained.

– Do not operate damaged equipment as the safety protection features

built into this product may have been impaired, either through physical
damage, excessive moisture, or any other reason. Remove power and do
not use the product until safe operation can be verified by service-trained
personnel. If necessary, return the product to the nearest Keysight
Technologies Sales and Service Office for service and repair to ensure the
safety features are maintained.

CAUTION

– Turn off circuit power and discharge all high-voltage capacitors in the

circuit before you perform resistance and capacitance measurements or

continuity and diode tests.

– Use the correct terminals, function, and range for your measurements.
– Do not measure voltage when current measurement is selected.
– Use only the recommended rechargeable battery. Ensure proper insertion

of battery in the instrument, and follow the correct polarity.

– Disconnect test leads from all the terminals during battery charging.

«
...
3
4
5
6
7
...
»

Содержание U1401B
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для U1401B

Бренд: Keithley Страницы: 48

Бренд: Yamaha Страницы: 3

Бренд: Quantel Страницы: 2

Бренд: ECO Sensors Страницы: 22

Бренд: ECO Sensors Страницы: 7

Бренд: F&F Страницы: 24

Бренд: QALCOMET Страницы: 52

Бренд: Ulvac Страницы: 24

Бренд: Veeder-Root Страницы: 59

Бренд: Hanna Instruments Страницы: 2

Бренд: DGH Страницы: 87

Veeder-Root 7990 Series

Бренд: Danaher Страницы: 8

Бренд: Yamaha Страницы: 8

Dakota Ultrasonics ZX-2

Бренд: ABQ Industrial Страницы: 27

Бренд: Aktobis Страницы: 7

IMI SENSORS 604B11

Бренд: PCB Piezotronics Страницы: 19

EUROGRAND EG2080

Бренд: Behringer Страницы: 34

Бренд: Lambda Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды