background image

N7040A/1A/2A Rogowski AC Current Probes User Guide

9

Overview

1

Features

Keysight provides three models (

N7040A, N7041A, and N7042A)

 under the Rogowski AC Current 

probes. The following tables list the key features of each of these models. 

N7040A 

4.5mm thick miniature clip-around Rogowski coil with 5kV peak 
insulation.

A novel electrostatic shielded Rogowski coil providing excellent immunity 
to interference from fast local dV/dt transients or large 50/60Hz voltages

Peak current rating upto 3.0kA

-3dB high frequency bandwidth upto 23MHz

-3dB low frequency bandwidth 3Hz

Peak di/dt capability upto 80kA/µs

Wide operating temperature from -40

o

C to +125

o

C

Terminated into 1M

Ω

 scope input

Positional accuracy typically ±2%

N7041A 

4.5mm thick miniature clip-around Rogowski coil with 5kV peak 
insulation.

A novel electrostatic shielded Rogowski coil providing excellent immunity 
to interference from fast local dV/dt transients or large 50/60Hz voltages

Peak current rating upto 0.6kA

-3dB high frequency bandwidth upto 30MHz

-3dB low frequency bandwidth 12Hz

Peak di/dt capability up to 40kA/µs

Wide operating temperature from -40

o

C to +125

o

C

Terminated into 1M

Ω

 scope input

Positional accuracy typically ±2%

Содержание N7040A











































Отзывы: