Keysight N7040A Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 42

background image

2

Safety and Regulatory Information

20

N7040A/1A/2A Rogowski AC Current Probes User Guide

Pre-Use Safety Checks and Warnings

WARNING

Indoor Use Only. Do not operate in wet / damp environments. Keep product

surfaces dry and clean.
Do not operate in an explosive environment.

CAUTION

The intended use of these probes is for the measurement of AC current.

Keysight Technologies accepts no responsibility for any damage resulting

from careless use, or failure to observe these instructions.

WARNING

If HAZARDOUS LIVE voltages are present and accessible in the installation,

appropriate protective measures must be taken to avoid electric shock.

WARNING

The integrity of the insulation around the Rogowski coil must be VISUALLY

INSPECTED before and after each use, and the probe must NOT BE USED if

there are signs of coil damage.

WARNING

Be extremely careful when using the coil of the probe on uninsulated

conductors. The power of the uninsulated conductor must be turned off

when applying or removing the probe’s coil from this conductor.
In addition, make sure that the probe is never used at voltages greater than

its voltage rating (safe PEAK working voltage) which is clearly labeled on

the probe cable adjacent to the coil. For N7040A and N7041A, it is 5kV peak

and for N7042A, it is 1.2kV peak.

WARNING

Voltage ratings are only valid if the ‘free end’ of the coil is fully inserted into

the probe’s ferule, and remains fully inserted during use. Refer to the topic

“Probe Handling Precautions"

on page 16 to know more.

«
...
18
19
20
21
22
...
»

Содержание N7040A











































Отзывы:

Нет отзывов

Похожие инструкции для N7040A

Бренд: ABQ Industrial Страницы: 15

Бренд: ABQINDUSTRIAL Страницы: 3

Бренд: Daewoo Страницы: 2

Wind Monitor Series

Бренд: Campbell Страницы: 38

Бренд: Favero Electronics Страницы: 12

Бренд: Keysight Страницы: 66

Бренд: aci Страницы: 5

Бренд: Palstar Страницы: 37

Бренд: LD Didactic Страницы: 2

TEMS AUTOMATIC - 2

Бренд: ASCOM Страницы: 12

Бренд: Armstrong Monitoring Corporation Страницы: 12

Бренд: Veeco Страницы: 349

Бренд: GrainPro Страницы: 7

Бренд: Caen Страницы: 50

Бренд: TAC Страницы: 28

EUROGRAND EG2080

Бренд: Behringer Страницы: 34

Бренд: STATICO Страницы: 21

Бренд: Badger Meter Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды