Keysight Technologies U3047AE04 Скачать руководство пользователя страница 75

Страница: 75 / 81

User’s and Service Guide U3047-90002

U3047AE04

Safety and Regulatory Information

Before Applying Power

Verify that the premises electrical supply is within the range of the instrument. The

instrument has an autoranging power supply.

If this product is not used as specified, the protection provided by

the equipment could be impaired. This product must be used in a

normal condition (in which all means for protection are intact) only.

The Mains wiring and connectors shall be compatible with the connector used

in the premise electrical system. Failure, to ensure adequate earth grounding

by not using the correct components may cause product damage, and serious

injury.

This product is designed for use in Installation Category II and Pollution

Degree 2, per IEC 61010 Second Edition.

Verify that the premise electrical voltage supply is within the range specified

on the instrument.

When installing the product in a cabinet, the convection into and out of the

product must not be restricted. The ambient temperature (outside the

cabinet) must be less than the maximum operating temperature of the

product by 4 °C for every 100 watts dissipated in the cabinet. If the total

power dissipated in the cabinet is greater than 800 watts, then forced

convection must be used.

This instrument has auto-ranging line voltage input, be sure the supply

voltage is within the specified range and voltage fluctuations do not to exceed

10 percent of the nominal supply voltage.

Содержание U3047AE04


















































































Результаты поиска

Содержание U3047AE04

Отзывы:

Похожие инструкции для U3047AE04

Бренды по названию

Популярные бренды

Keysight Technologies U3047AE04, Руководство пользователя и сервисное руководство

Результаты поиска

Содержание U3047AE04

Отзывы:

Похожие инструкции для U3047AE04

Бренды по названию

Популярные бренды