background image

17 

 

OZG_497-BA-e-1510 

5.9  Changing the bulb 

 
Halogen 

 

Before  changing  the  halogen  bulb,  you  must  always 

switch  off

  the  device  and 

unplug  it  from  the  mains

.  You  must  also  make  sure  that  the

  bulb  and  housing 

have cooled down, so that you avoid any risk of possible burn injuries.  
 
To  change  the  bulb,  the  whole  lamp  housing,  fitted  underneath  the  working  stage, 
has to be removed. Therefore you have to tip the device carefully to the back or side 
and then loosen the fixing screws (Allen wrench) at the bottom of the working stage. 
When doing this, please make sure that all microscope components are firmly fixed. 
The bulb which appears inside the open lamp housing can then be simply pulled out 
of its socket and replaced with a new bulb. You must then position and fix again the 
housing correctly.  
 

Please always use cloth gloves or similar to hold and fit a new bulb otherwise 
grease and dust residue on the surface of the bulb could have a negative effect 
on its brightness and service life. 

 
 

5.10  Changing the fuse 

 
There is a fuse 

on the rear of the microscope stand base (label: “Fuse”). 

If the fuse has blown, then with the device switched off and the power disconnected, 
the fuse can easily be unscrewed using a flat blade screw driver and replaced with a 
new one. 

 

Содержание OZG 497






















Отзывы: