
TK-5310
2
GENERAL / SYSTEM SET-UP
Document Copyrights
Copyright 2006 by Kenwood Corporation. All rights
reserved.
No part of this manual may be reproduced, translated,
distributed, or transmitted in any form or by any means,
electronic, mechanical, photocopying, recording, or other-
wise, for any purpose without the prior written permission
of Kenwood.
Disclaimer
While every precaution has been taken in the preparation
of this manual, Kenwood assumes no responsibility for
errors or omissions. Neither is any liability assumed for dam-
ages resulting from the use of the information contained
herein. Kenwood reserves the right to make changes to any
products herein at any time for improvement purposes.
INTRODUCTION
SCOPE OF THIS MANUAL
This manual is intended for use by experienced technicians
familiar with similar types of commercial grade communications
equipment. It contains all required service information for the
equipment and is current as of the publication date. Changes
which may occur after publication are covered by either Service
Bulletins or Manual Revisions. These are issued as required.
ORDERING REPLACEMENT PARTS
When ordering replacement parts or equipment information, the
full part identification number should be included. This applies to all
parts : components, kits, or chassis. If the part number is not known,
include the chassis or kit number of which it is a part, and a sufficient
description of the required component for proper identification.
PERSONAL SAFETY
The following precautions are recommended for personal safety:
• DO NOT transmit until all RF connectors are verified se-
cure and any open connectors are properly terminated.
• SHUT OFF and DO NOT operate this equipment near elec-
trical blasting caps or in an explosive atmosphere.
• This equipment should be serviced by a qualified technician only.
SERVICE
This transceiver is designed for easy servicing. Refer to
the schematic diagrams, printed circuit board views, and
alignment procedures contained within.
NOTE
You must use KPG-95D version 5.00 or later for this trans-
ceiver. KPG-95D versions earlier than version 5.00 will not
work properly.
SYSTEM SET-UP
Merchandise received
License and frequency allocated by FCC
Choose the type of transceiver
Transceiver programming
Are you using the optional antenna?
Are you using the speaker microphone?
A personal computer (IBM PC or compatible), programming interface (KPG-36/36A), USB
adapter(KCT-53U), and programming software (KPG-95D) are required for programming.
(The frequency, and signaling data are programmed for the transceiver.)
Frequency range (MHz)
RF power
Type
LCD 4-key DTMF keypad
TX/RX 450~520
4W
TK-5310 K
No
No
No
No
TX/RX 450~520
4W
TK-5310 K2
Yes
Yes
TX/RX 450~520
4W
TK-5310 K3
Yes
Yes
Yes
No
TX/RX 380~470
4W
TK-5310 K4
No
No
TX/RX 380~470
4W
TK-5310 K5
Yes
Yes
No
Yes
TX/RX 380~470
4W
TK-5310 K6
Yes
Yes
YES
KRA-23 or KRA-27
Helical antenna
NO
NO
(Option)
(Option)
YES
KMC-25
Speaker microphone
or
KMC-38GPS
GPS speaker microphone
Are you using the voice guide & storage unit?
NO
(Option)
YES
VGS-1
Delivery
See page 10
Model &
Unit
X57-725X-XX
Frequency range
Remarks
LCD
4-key
DTMF
Destination (Market code)
0-10 0-11 0-12 0-13 0-14 0-15
keypad
K
✓
-
-
-
K2
✓
450~520 MHz
✓
✓
-
TK-5310
K3
✓
1st IF:49.95MHz
✓
✓
✓
K4
✓
LOC:50.4MHz
-
-
-
K5
✓
380~470 MHz
✓
✓
-
K6
✓
✓
✓
✓
Содержание TK-5310
Страница 96: ...TK 5310 91 MEMO ...