Kenwood TH-D72A, Руководство по обслуживанию

Страница: 42 / 97

TH-D72A/D72E
42
• I. Balance 2
1) Display the “BAL2” item.
2) Select display frequency point after press [
X
OK] key at
“BAL2” item.
3) While press [PTT], press [
S
], [
T
] key and turn the en-
coder during transmission to change the “adjustment
value”.
4) Press [
X
OK] key to set the “adjustment value” in the
EEPROM.
5) Set item the display to “VHF Cent”, “VHF Lo”, “VHF
Hi”, “UHF Cent”, “UHF Lo” and “UHF Hi” and adjust all
frequency adjustment points.
2 L A B
0 8
0 8 1
EEPROM setting
adjustment value
Frequency adjustment point
D
e n C C F H V
E V
t
W
1
• J. CTCSS deviation
1) Display the “CT DEV” item.
2) Select display frequency point after press [
X
OK] key at
“CT DEV” item.
3) While press [PTT], press [
S
], [
T
] key and turn the en-
coder during transmission to change the “adjustment
value”.
4) Press [
X
OK] key to set the “adjustment value” in the
EEPROM.
5) Set item the display to "“VHF Cent”, “VHF Lo”, “VHF
Hi”, “UHF Cent”, “UHF Lo” and “UHF Hi” and adjust all
frequency adjustment points.
D L T C
9 2
9 2 1
EEPROM setting
adjustment value
Frequency adjustment point
E
e n C C F H V
V V
t
W
• K. DCS deviation
1) Display the “DCS DEV” item.
2) Select display frequency point after press [
X
OK] key at
“DCS DEV” item.
3) While press [PTT], press [
S
], [
T
] key and turn the en-
coder during transmission to change the “adjustment
value”.
4) Press [
X
OK] key to set the “adjustment value” in the
EEPROM.
5) Set item the display to “VHF Cent”, “VHF Lo”, “VHF
Hi”, “UHF Cent”, “UHF Lo” and “UHF Hi” and adjust all
frequency adjustment points.
D S C D
3 2
3 2 1
EEPROM setting
adjustment value
Frequency adjustment point
D
e n C C F H V
E V
t
W
Note: CTCSS/DCS DECODE adjustment
Perform CTCSS/DCS DECODE adjustment with S-meter
adjustment at “V SM/SQ A SM FULL”.
• L. VOX gain adjustment
1) Display the “VOX” item.
2) Select “VOX1” item after press [
X
OK] key at “VOX”
item.
3) Enter the voltage of level 1 of the VOX gain.
4) Press [
X
OK] key to set the “adjustment value” in the
EEPROM.
5) Select “VOX9” item after press [
X
OK] key at “VOX”
item.
6) Enter the voltage of level 9 of the VOX gain.
7) Press [
X
OK] key to set the “adjustment value” in the
EEPROM.
D X O V
4 0
4 0 2
EEPROM setting
adjustment value
D
e n C
1 X O V E V
t
W 2
• M. BPF
1) Display the “VHF BPF A” item.
2) Select points “Low” to “High” as shown in the “Fre-
quency Adjustment Points” table below.
3) Press [MONI] key because “Max RSSI Value” select au-
tomatic and set the “adjustment value” in the EEPROM.
4) Adjust all frequency adjustment points.
D F H V
0 0
0 0 1
EEPROM setting
adjustment value
B
1
w o L
P F
t
A
RSSI value Frequency adjustment point
A
1
0 0 1
• If “MAX RSSI value” is less “70”, it can’t set in the EE-
PROM.
Adjustment frequency points table
Band Item Frequency
VHF BPF A
Low 136.05MHz
Center 145.95MHz
High 173.95MHz
UHF BPF A
Low 410.05MHz
Center 439.95MHz
High 469.95MHz
VHF BPF B
Low 118.05MHz
Center 145.95MHz
High 173.95MHz
UHF BPF B
Low 320.05MHz
LowD 380.05MHz
Center 439.95MHz
HighD 479.95MHz
High 523.95MHz
ADJUSTMENT