26
Data Size:
B6L (182 mm x 128 mm)
Book Size:
B6L (182 mm x 128 mm)
REFERENCES
Change the display information
Each time you press
DISP
, the display information changes.
•
If the information is unavailable or not recorded, “NO TEXT”, “NO INFO”, or other information
(eg. station name, playing time) appears.
Source name
Display information
STANDBY
Source name (Date/Clock)
*
TUNER
Frequency (Date/Clock)
*
(For FM Radio Data System stations only)
Station name (Date/Clock)* Radio text (Date/Clock)* Radio text+
(R.TEXT+) Title (Artist) Title (Date/Clock)* Frequency (Date/Clock)*
(back to the beginning)
USB
(For MP3/WMA/AAC/WAV/FLAC files)
Music title (Artist) Music title (Album title) Music title (Date/Clock)*
File name (Folder name) File name (Date/Clock)* Playing time (Date/
Clock)* (back to the beginning)
iPod USB/
iPod BT or
ANDROID
When
[MODE OFF]
/
[BROWSE MODE]
is selected.
( 9)
Music title (Artist) Music title (Album name) Music title (Date/Clock)*
Playing time (Date/Clock)* (back to the beginning)
PANDORA/
PANDORA BT
Station name (Date/Clock)* Shared/Radio station (Date/Clock)*
Music title (Artist) Music title (Album title) Music title (Date/Clock)*
Playing time (Date/Clock)* (back to the beginning)
BT AUDIO
Music title (Artist) Music title (Album name) Music title (Date/Clock)*
Playing time (Date/Clock)* (back to the beginning)
AUX
Source name (Date/Clock)*
*
Battery and signal strength of the Bluetooth device will be shown if
[BATT/SIGNAL]
is set to
[AUTO]
.
( 14)
INSTALLATION/CONNECTION
Warning
•
The unit can only be used with a 12 V DC power supply, negative ground.
•
Disconnect the battery’s negative terminal before wiring and mounting.
•
Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire
(black) to prevent a short circuit.
•
Insulate unconnected wires with vinyl tape to prevent a short circuit.
•
Be sure to ground this unit to the car’s chassis again after installation.
Caution
•
For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
•
Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during
and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
•
Do not connect the
[
wires of speakers to the car chassis or Ground wire (black), or connect
them in parallel.
•
Mount the unit at an angle of less than 30º.
•
If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red)
to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned
on and off by the ignition key.
•
Keep all cables away from heat dissipate metal parts.
•
After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are
working properly.
•
If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old
fuse with one that has the same rating.
Basic procedure
1
Remove the key from the ignition switch, then disconnect the
[
terminal of the car
battery.
2
Connect the wires properly.
See Wiring connection.
( 28)
3
Install the unit to your car.
See Installing the unit (in-dash mounting).
( 27)
4
Connect the
[
terminal of the car battery.
5
Press
to turn on the power.
6
Detach the faceplate and reset the unit. ( 3)
ENGLISH
JS_KWD_KMM_BT303_MN_EN_1.indd 26
JS_KWD_KMM_BT303_MN_EN_1.indd 26
10/6/2016 10:21:43 AM
10/6/2016 10:21:43 AM
