NX-200
4
2. How to Enter Each Mode
Mode
Operation
User mode
Power ON
Panel test mode
[ ] + Power ON
PC mode
Received commands from PC
Panel tuning mode
[Panel test mode] + [ ]
Firmware programming
mode
[ ] + Power ON
Clone mode
[ ] + Power ON
Firmware version
information
[Side1] + Power ON
3. Panel Test Mode
Setting method refer to ADJUSTMENT.
4. Panel Tuning Mode
Setting method refer to ADJUSTMENT.
5. PC Mode
5-1. Preface
The transceiver is programmed by using a personal com-
puter, programming interface (KPG-36/36A), USB adapter
(KCT-53U) and programming software (KPG-111D).
The programming software can be used with a PC or
compatible. Figure 1 shows the setup of a PC for program-
ming.
MI
C
PC
KPG-111D
KPG-36 or KPG-36A or
KPG-36A + KCT-53U
Illustration is KPG-36.
KPG-36
Transceiver
PC
D-SUB
(25-pin)
Transceiver
PC
KPG-36A
D-SUB
(9-pin)
Transceiver
PC
KPG-36A
KCT-53U
USB
Fig. 1
5-2. Connection procedure
1. Connect the transceiver to the computer using the inter-
face cable and USB adapter (When the interface cable is
KPG-36A, the KCT-53U can be used.).
Note:
• You must install the KCT-53U driver in the computer to
use the USB adapter (KCT-53U).
• When using the USB adapter (KCT-53U) for the fi rst time,
plug the KCT-53U into a USB port on the computer with
the computer power ON.
2. When the POWER switch on, user mode can be entered
immediately. When PC sends command the transceiver
enter PC mode, and “PROGRAM” is displayed on the
LCD.
When data transmitting from transceiver, the red LED is
lights.
When data receiving to transceiver, the green LED is
lights.
Note:
The data stored in the computer must match the “Model
Name” when it is written into the fl ash memory.
5-3. KPG-36/KPG-36A description
(PC programming interface cable: Option)
The KPG-36/36A is required to interface the transceiver
to the computer. It has a circuit in its D-sub connector (KPG-
36: 25-pin, KPG-36A: 9-pin) case that converts the RS-232C
logic level to the TTL level.
The KPG-36/36A connects the universal connector of the
transceiver to the RS-232C serial port of the computer.
5-4. KCT-53U description (USB adapter: Option)
The KCT-53U is a cable which connects the KPG-36A to
a USB port on a computer.
When using the KCT-53U, install the supplied CD-ROM
(with driver software) in the computer. The KCT-53U driver
runs under Windows 2000, XP or Vista (32-bit).
5-5. Programming software KPG-111D description
The KPG-111D is the programming software for the
transceiver supplied on a CD-ROM. This software runs un-
der MS-Windows 2000, XP or Vista (32-bit) on a PC or com-
patible machine.
The data can be input to or read from the transceiver and
edited on the screen. The programmed or edited data can
be printed out. It is also possible to tune the transceiver.
6. Firmware Programming Mode
6-1. Preface
Flash memory is mounted on the transceiver. This al-
lows the transceiver to be upgraded when new features
are released in the future. (For details on how to obtain the
fi rmware, contact Customer Service.)
REALIGNMENT
